Lightware HDMI-TPS-TX220 Bruksanvisning

Läs gratis den bruksanvisning för Lightware HDMI-TPS-TX220 (2 sidor) i kategorin AV extender. Guiden har ansetts hjälpsam av 26 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 5 recensioner. Har du en fråga om Lightware HDMI-TPS-TX220 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Quick Start Guide

DVI-HDCP-TPS-TX210, DVI-HDCP-TPS-TX220

HDMI-TPS-TX210, HDMI-TPS-TX220

DP-TPS-TX210, DP-TPS-TX220

Further information

The document is valid with the following rmware version: 1.1.4

The User’s manual of this appliance is available at www.lightware.com.

See the Downloads section on the dedicated product page.

Contact us

[email protected]

+36 1 255 3800

[email protected]

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 2.1

19200111

Important Safety Instructions

Please read the supplied safety instruction document before using the product and keep it

available for future reference.

Introduction

Thank you for choosing Lightware TPS-TX200 series transmitter. The products have

HDBaseT

TM

integration with additional Lightware developments. The devices transmit HDMI/

DVI digital video signal up to 4K resolution, audio and control up to 170 m distance over a

single CAT cable (in case of DP-TPS transmitters the DP signal is converted to HDMI).

Compatible Devices

The transmitters are compatible with all Lightware

TPS receivers, matrix boards and third party

devices based on HDBase-T

TM

technology.

Power Supply Options

The transmitters can be powered:

Locally with the supplied 12V DC adaptor or Lightware’s rack mountable PSU, or

Remotely by a PoE-compatible power injector, like Lightware’s TPS-PI-1P1.

For more information please turn the paper.



TPS-TX/RX95 are not PoE-compatible, thus not able to remote power the TPS-TX200

series and vica versa. TPS-TX200 series contains PoE-compatible remote power function,

RX95 can be remote powered only by TX95 transmitter.

HDBaseT

TM

and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Box ContentsConnecting Steps

* Only for DVI-HDCP-TPS-TX220, HDMI-TPS-TX220 and DP-TPS-TX220 models.

Front Views

Rear Views

Front Panel LEDs

Video Source

OFF: video source is not selected.

BLINKING: video source is selected but not active.

ON: video source is selected and active.

Audio Sources

OFF: audio source is not selected.

BLINKING: audio source is selected but not active.

ON: (with short pause): audio source is selected and the port is active but not embedded

to the output video stream (DVI output mode).

ON: (continuously): audio source is selected, the port is active and the audio is embedded

to the output video stream (HDMI output mode).



When Autoselect is enabled and audio signal is not present at all, audio LEDs blink.

HDCP LED

OFF: video output signal is not encrypted with HDCP.

ON: video output signal is encrypted with HDCP.

Autoselect LED

OFF: autoselect is disabled.

BLINKING: autoselect is enabled; searching for signal (audio LEDs also blink).

ON: autoselect is enabled; active signal is found (the LED of selected audio also lights).

Rear Panel LEDs

LIVE

OFF: device is not powered.

BLINKING (slow): device is powered and operational.

BLINKING (fast): device is in bootload mode.

ON: device is powered but no operation.

RS-232 LED

OFF: RS-232 ports (local and link) are in Pass-through mode.

BLINKING: command injection mode is active.

ON: RS-232 ports (local and link) are in Control mode.

SRVC

Reserved for future developments.

LINK

OFF: no TPS link between transmitter and receiver.

BLINKING (slow): low power mode is active.

BLINKING (fast): Ethernet fallback mode is active.

ON: TPS link is established, HDBaseT or Long Reach mode is active.

1

Autoselect LEDLED gives feedback about the current Autoselect status.

2

HDCP LEDLED gives feedback about the HDCP status of the output

signal.

3

DisplayPort inputDisplayPort connector for DisplayPort audio/video signal.

4

HDMI inputHDMI connector for DVI video or HDMI video and audio.

5

DVI-D inputDVI-I connector for DVI-D video and audio.

6

Audio input3.5 mm Jack connector for unbalanced analog audio

input signal.

7

Video select

button

Button for selecting a video source.

8

Audio select

button

Button for selecting an audio source.

9

Show me buttonSpecial functions can be reached using this button

(rmware upgrade (bootload) mode, DHCP settings,

restore factory default settings, condition launching in

Event Manager).

1

DVI-D outputLocal DVI-D output with the same A/V content as the

TPS output.

2

HDMI outputLocal HDMI output with the same A/V content as the TPS

output.

3

TPS outputLocking RJ45 connector for HDBaseT

TM

signal

transmission.

4

EthernetLocking RJ-45 connector for conguring the device using

Lightware Device Controller (LDC), or upgrading it using

Lightware Device Updater (LDU). Any third-party control

system can use this port to control the device.

5

Status LEDsThe LEDs give feedback about the actual state of the

device.

6

IR IN and IR OUT3-pole TRS connector, also known as 3.5 mm (1/8”) jack

plug for optional IR receiver (IR IN) and transmitter (IR

OUT) connection.

7

GPIO port8-pole Phoenix connector for congurable general

purpose input/output ports.

8

RS-232 port3-pole Phoenix connector for controlling the device by

LDC or third-party control systems.

9

12V DC input12V DC input for local powering.

Transmitter unit12V DC power adaptor

with interchangeable plugs

Infrared transmitter unit

Phoenix combicon

3-pole connector

Phoenix combicon

8-pole connector*

Safety and warranty info,

Quick Start Guide

Safety and

Warranty

Info

Quick

Start

Guide

Locking DC Plug

Twist 90° clockwise to lock.

DVI

Connect the source (e.g. a PC) to the DVI-I input port by a DVI cable.

Audio

Connect an audio source (e.g. a Media player) to the 3.5 analog audio input

port.

CATx

DVI

Connect the TPS output port of the transmitter to the TPS+PoE port of the

TPS-PI-1P1 by a CATx cable.

Connect the receiver (or the Matrix input board) to the power injector by a

CATx cable via the TPS port.

RS-232

Optionally for RS-232 extension: connect a controller/controlled device

(e.g. Touch panel) to the RS-232 port.

IR

Optionally for Infrared extension:

Connect the IR emitter to the IR OUT port of the transmitter, and/or

Connect the IR detector to the IR IN port of the transmitter.

LAN

Optionally connect the transmitter to a LAN.

GPIO

Optionally connect the transmitter to a LAN.

Power

Powering on the devices is recommended to do as the nal step during the

installation. Please see the Power Supply Optionssection for the details.

2 pole, 1 ring: IR transmitter3 pole, 2 rings: IR receiver

Types of IR connectors (1/8” TRS / TS)

RS-232

AudioDVI-I

GPIO

Media player

IR

Ethernet

Infrared

Relay box

LAN

Touch panel

PC

DVI-HDCP-TPS-TX220

Autoselect

HDCP

DVI-D IN

AUDIO IN

SHOW

ME

AUDIO

SELECT

RESET

VIDEO

AUDIO

AUDIO

Power

Compatible

TPS Receiver

CATx

23167

9

258167

9

248167

9

HDMI-TPS-TX220

DVI-HDCP-TPS-TX220

DP-TPS-TX220

234576

9

8

134576

9

8

HDMI-TPS-TX220, DP-TPS-TX220

DVI-HDCP-TPS-TX220

Produktspecifikationer