Livex Lighting Rotterdam 46180-46 Bruksanvisning
Sidor 2 Engels Lättnad
Läs bruksanvisningen för Livex Lighting Rotterdam 46180-46 gratis online eller ladda ner PDF:en. 24 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the installation
instructions do apply to this product.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1).
1. Shut off the power at the circuit breaker and remove old fixture from ceiling,
including the old mounting plate.
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Attach the mounting plate (A) to the junction box using screws (B).The side of
the mounting plate marked “GND” must face out. The junction box is not
included.
4.
While holding the lamp body towards the junction box,guide supply wires
through hole in center of mounting plate. Follow wiring instructions carefully
(see fig.2).
5. Place the Canopy (C) over the ceiling junction box, aligning the mounting holes
with the thread holes in the mounting plate(A). Secure the Canopy (C) by
tightening the Canopy Screws (D).
6. Attach the glass shade (E) and the nut (F) onto the socket of the lamp body, then
securely tighten the nut (F) using the wrench (G), then remove the socket wrench
and save it.
7. Install the light bulb (Not included)in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
CONNECTING THE WIRES (Fig.2)
1. Take the black wire from the ceiling junction box and the black wire from the
fixture and twist bare ends together. Twist wire connector onto end of wire until
snug.
2. Repeat same process with white junction box wire and white fixture wire. NOTE:
Twist wires together in the same direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper), attach this wire
and the bare copper wire from the fixture together as step 1. If junction box has no
ground wire, attach the bare copper fixture wire to the green ground screw on the
mounting plate.
4. Tuck the wire connections neatly into the junction box.
Your installation is now complete. Return power to the junction box and test
the fixture.
FIG.1
FIG.2
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black (Hot)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper (Ground)
Produktspecifikationer
| Varumärke: | Livex Lighting |
| Kategori: | Lättnad |
| Modell: | Rotterdam 46180-46 |
Behöver du hjälp?
Om du behöver hjälp med Livex Lighting Rotterdam 46180-46 ställ en fråga nedan och andra användare kommer att svara dig
Lättnad Livex Lighting Manualer
Livex Lighting 7390-91 Bruksanvisning Livex Lighting Meridian 51084-91 Bruksanvisning Livex Lighting Everett 52830-91 Bruksanvisning Livex Lighting Glendon 53640-01 Bruksanvisning Livex Lighting Villa Verona 8565-63 Bruksanvisning Livex Lighting Arabesque 41111-92 Bruksanvisning Livex Lighting Carlisle 51098-92 Bruksanvisning Livex Lighting Meridian 51082-91 Bruksanvisning
Alla Livex Lighting Lättnad manualer
Populära i Lättnad
Livex Lighting Park Ridge 6352-91 Bruksanvisning Livex Lighting Jefferson 5082-04 Bruksanvisning Livex Lighting Meridian 51085-91 Bruksanvisning
Lättnad Manualer
Nyaste Lättnad Manualer
Schonbek Kodo S7822-18H Bruksanvisning DCW AARO Wall Bruksanvisning DCW FOCUS X5 Bruksanvisning Maginon TL-380W Bruksanvisning Nitecore CL10 Bruksanvisning Nitecore HA23 UHE Bruksanvisning Kinotehnik Practilite 632 Bruksanvisning American DJ Hydro Wash X19 Bruksanvisning American DJ Saber Spot RGBW Bruksanvisning Yongnuo YNRAY260 Bruksanvisning