Livex Lighting Carlisle 51098-92 Bruksanvisning
Livex Lighting
Lättnad
Carlisle 51098-92
Läs gratis den bruksanvisning för Livex Lighting Carlisle 51098-92 (2 sidor) i kategorin Lättnad. Guiden har ansetts hjälpsam av 13 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 7 recensioner. Har du en fråga om Livex Lighting Carlisle 51098-92 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
51028 51029 51097 51098
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut o the power at the circuit breaker box. Remove old xture and all hardware
from Junction Box. Carefully unpack your new xture and lay out all the parts on a
clear area. Take care not to lose any small parts necessary for installation.
2. Attach the pipe thread part way into the center hole of the single bar and secure
with hex nut. Attach the single bar to the junction box using two box screws as
shown. The side of the single bar marked “GND” must face out. The junction box
is not included.
3. Please see the Fig 1.1 (round frame Top View). Loosen the tie crystal cluster of
cord and organize appropriate. Raise the column(H) to the bottom of the lamp
body(I), by turn it clockwise until tight. Raise the acrylic plate(C), round frame (D)
to the bottom of the lamp body (I), aligning the center hole with pipe nipple and
screw it with the finial (G) until tight.
4. Raise the end grapnel of the crystal cluster(E) hook the middle ring of round
frame(D); raise the end grapnel of the crystal cluster(F) hook the inside ring of
round frame(D). Holding the hook of shade(B) insert the small hole of the lamp
body’s plate.
5. While holding the lamp assembly towards the ceiling, connect the electrical wires
as Shown in Fig.2, making sure that all wire nuts are secured. You may have to
wrap the connections with electrical tape. If your outlet has a ground wire (green
or bare copper), connect the fixture ground wire to it. Otherwise connect fixture’s
ground wire directly to the mounting plate with the green screw provided. After
wires are connected, tuck them carefully inside the Junction Box.
6. Raise the lamp assembly onto the junction box, aligning screws on single bar with
mounting holes in lamp body(H) and lock it securely with the ball nut (A).
7. Install the light bulbs(Not included) in accordance with the fixture’s specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
Your installation is now complete. Return power to the junction
box and test the fixture.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20161151028
FIG.2
Produktspecifikationer
| Varumärke: | Livex Lighting |
| Kategori: | Lättnad |
| Modell: | Carlisle 51098-92 |
Behöver du hjälp?
Om du behöver hjälp med Livex Lighting Carlisle 51098-92 ställ en fråga nedan och andra användare kommer att svara dig
Lättnad Livex Lighting Manualer
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
Lättnad Manualer
- Gardena
- Aqara
- Ape Labs
- Stanley
- Elation
- ILive
- Nordlux
- Ludeco
- Honeywell
- Cotech
- BeamZ
- Genaray
- Chamberlain
- IXL
- SolarlampKoning
Nyaste Lättnad Manualer
9 April 2025
9 April 2025
9 April 2025
8 April 2025
8 April 2025
8 April 2025
7 April 2025
5 April 2025
5 April 2025
5 April 2025