M-Audio CT-14 Bruksanvisning

M-Audio Inte kategoriserad CT-14

Läs nedan 📖 manual på svenska för M-Audio CT-14 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 5 personer och betygsatt med 3.9 stjärnor i genomsnitt av 3 användare

Ladda ner PDF

Sida 1/4

CT-14

™

1x4 Digital Audio

Coaxial S/PDIF

Thru Box

CT-14

MANUAL

CT-14

1x4 Digital Audio Coaxial S/PDIF Thru Box

Thank you for purchasing the CT-14, by M Audio. The CT-

14 accepts one S/PDIF digital audio signal via coaxial RCA

connector and duplicates it to four S/PDIF coaxial RCA

outputs, all on the rear of the CT-14. This allows you to

take the S/PDIF output of any digital audio source, such

as a DAT, CD player, digital mixer, etc., and send it

simultaneously to four digital audio targets that are

capable of receiving S/PDIF format signals. The CT-14

will flawlessly pass any coaxial S/PDIF signal having

100kHz or less sample rate and any data width. Its

active electronics assure that the integrity of your digital

signal is never compromised.

The setup example that follows shows what might be a

typical mixing scenario. The output of a digital mixer is

connected to the CT-14 input, while a DAT, computer-

based digital audio card (such as an M Audio “Delta DiO

2496” or “DiO 2448”), a CD recorder, and a D/A

Converter (to feed your monitors) are connected to the

CT-14 outputs. This setup allows the user to take one

mix output and simultaneously record to several mixdown

decks, saving hours of time and possible frustration.

To set up the CT-14 in your system, first make sure all of

your external devices are turned off. Then, using good-

quality 75-ohm coaxial digital cables with male connectors

(digital video cables meet this requirement) for best

results, follow this simple procedure:

1. With the CT-14 power button in the “out” (off) position, plug the

appropriate end of the supplied 9-Volt DC “wall-wart” power

adapter into your CT-14 and the other end into a wall socket or

power strip. The CT-14 power indicator LED should be off.

2. Take the output of your digital audio source device and plug it into

the CT-14 coaxial RCA input connector located on the rear of the

CT-14 .

3. Connect the CT-14’s coaxial RCA digital output connectors to the

inputs of your receiving or “target” digital audio devices. You may

want to connect the analog audio output of one of these target

devices to a sound system for monitoring purposes.

4. With all volumes turned down, turn on your source device.

5. Turn on the CT-14 by pressing its power button and allowing it to

latch in the “in” position. The power indicator LED will light on the

front of the CT-14 unit.

6. Turn on your target devices. Your CT-14 is now ready for use.

CT-14

Hook-Up

Diagram

Produktspecifikationer

Varumärke:	M-Audio
Kategori:	Inte kategoriserad
Modell:	CT-14
Färg på produkten:	Zwart
Inbyggd display:	Ja
Vikt:	113 g
Bredd:	87.6 mm
Djup:	17 mm
Höjd:	64.8 mm
Typ av strömkälla:	Batterij/Accu
Medföljande kablar:	Micro-USB
Ljudlarm:	Ja
Ljuslarm:	Ja
Levensduur batterij:	4 uur
Type beeldscherm:	Kleurenscherm
Energiadapter för bil ingår:	Ja
Hastighetsgräns:	Ja
Kontinuerlig hastighetsindikering:	Ja
Prenumeration krävs:	Ja