Martin 516 Dimmer-Controller Bruksanvisning
Martin
Inte kategoriserad
516 Dimmer-Controller
Läs gratis den bruksanvisning för Martin 516 Dimmer-Controller (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 6 recensioner. Har du en fråga om Martin 516 Dimmer-Controller eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
The Martin
516 Dimmer-Controller
users guide
CONTENTS
INTRODUCTION ................................................. 3
INSTALLING THE 516 DIMMER CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
OPERATING WITH A MARTIN LIGHTING CONTROLLER . . . . . . . . . . . . . . . . . . . 4
DIP-SWITCH SETTINGS TABLE FOR THE 516 DIMMER-CONTROLLER . . . . . . . . 5
TECHNICALSPECIFICATIONS....................................... 5
INTRODUCTION
The Martin Professional enables the Martin range of intelligent516 Dimmer-Controller
lighting controllers to control analog lighting and smoke equipment which require a 0-10V
fader control voltage.
INSTALLING THE 516 DIMMER CONTROLLER
Your Martin Professional 516 Dimmer-Controller package comes complete with the following
items:
516 Dimmer-Controller.
5 metre XLR/XLR cable.
Users guide.
IMPORTANT
Before attempting any of the following please ensure that the units are
disconnected from any AC power.
Setting the supply voltage:
Located on the back of the controller is a mains voltage selector. You must set it so that it
matches your local mains voltage.
Fitting the mains plug:
The 516 Dimmer-Controller may be delivered without a plug on the mains lead. You will
need to t a suitable plug (one that ts your local mains socket) before you can connect it
to the mains. The double insulated mains lead on the 516 Dimmer-Controller contains three
wires. Connect the Brown wire to the LIVE-pin, the Blue wire to the NEUTRAL-pin and the
Yellow/Green wire to the EARTH-pin in the mains plug.
2
Connecting the 516 Dimmer-Controller to the Martin Serial Link:
The 516 Dimmer-Controller responds to information sent from any of the Martin Lighting
Controllers: 3032, 2032, 2308 or 2208. As far as the Lighting Controller is concerned, the
516 Dimmer-Controller is similar to any Martin Intelligent Lighting Unit (ie. Roboscan,
Robocolor, Robozap etc.). For this reason the 516 Dimmer-Controller will sometimes be
referred to as a Lighting Unit in the following text. Please use the following procedure to set
up the Martin Serial Link.:
Connect the rst lighting unit (which could be your 516 Dimmer-Controller) to your Martin
Lighting Controller (2208/2308/2032/3032) using the XLR/XLR or XLR/D-SUB cable which
came with the lighting controller.
If you are using one 516 Dimmer-Controller only, then insert the male XLR termination
plug, which came with your lighting controller, into the unused XLR socket on the 516
Dimmer-Controller.
If you are using other lighting units (Roboscans, Robocolors, Robozaps etc.) with the
lighting controller then connect these together with XLR/XLR cables like the one that
came with your 516 Dimmer-Controller. The last unit on the link should be terminated
with the male XLR termination plug. You may connect up to 32 units on the same link.
Using 516 Dimmer-Controllers only, this will give you 32 * 16 = 512 analog outputs.
Located on the back of the Dimmer-Controller is the address selection DIP-switch. Use
this switch to set your 516 Dimmer-Controller to the desired controller channel as
shown in the address setting table on page 4. Note that the 516 Dimmer-Controller
only requires one controller channel to control all 16 analog outputs.
Connecting the 516 Dimmer-Controller to your analog equipment:
Located on the back of the 516 Dimmer-Controller is a 25 pin D-SUB connector plus four
5 pin DIN sockets from which the analog output is provided. Use these to connect the 516
Dimmer-Controller to your analog equipment. The relation between channel numbers and
pin numbers is listed on the label located directly above the connectors.
Placing the 516 Dimmer-Controller:
The 516 Dimmer-Controller ts into any standard 19" rack. Alternatively, you can choose to
place the 516 Dimmer-Controller on its four rubber feet.
OPERATING WITH A MARTIN LIGHTING CONTROLLER
You may now switch on your 516 Dimmer-Controller followed by your Martin Lighting
Controller. Please refer to the users guide for your Martin Lighting Controller for further
operating instructions.
3
Produktspecifikationer
| Varumärke: | Martin |
| Kategori: | Inte kategoriserad |
| Modell: | 516 Dimmer-Controller |
Behöver du hjälp?
Om du behöver hjälp med Martin 516 Dimmer-Controller ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Martin Manualer
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
24 September 2024
24 September 2024
23 September 2024
Inte kategoriserad Manualer
- Eligent
- OM SYSTEM
- Comatec
- Saitek
- AVTech
- Rupert Neve Designs
- DiversiTech
- Europa Leisure
- MagnaPool
- Clage
- Faytech
- SIG Sauer
- KM-fit
- HQ Power
- Durex
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025