Metra 99-7413 Bruksanvisning
Metra
Inte kategoriserad
99-7413
Läs gratis den bruksanvisning för Metra 99-7413 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 5 recensioner. Har du en fråga om Metra 99-7413 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
99-7413
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
NISSAN
Altima 1993-97........................................................... 1
Altima 1998-01........................................................... 2
KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Wrench
Phillips screwdriver
Equalizer
Dummy Plate
(6) #6 Self-tapping
Screws
(4) 5mm Flat-head
Screws
Radio Housing
Faceplate
ISO-DIN
Spacers
Mounting
Brackets
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the shifter cover and (4) Phillips screws
exposed. Remove (2) screws from the
driver's side knee bolster and lower.
Remove (1) screw from the left corner of the
radio triim bezel. Remove (2) screws above
the radio opening and unclip the bezel.
Remove (4) screws from the factory head
unit assembly and disconnect the wiring.
Using the raised lines as a guide, cut and
remove the ends of each Mounting Bracket
("A").
Align the holes in the Mounting Brackets
with the holes in the and Radio Housing
mount with (6) #6 Self-tapping Screws
supplied.
Remove (4) screws securing the cupholder
to the factory head unit assembly and
remove. Slide the cupholder into the bottom
of the Radio Housing and mount with the
same (4) screws. Skip to the Installation
Instructions for ALL VEHICLES on Page #3.
NISSAN Altima 1993-97
1
4
2
3
1
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the gear shifter trim bezel and remove (2)
Phillips screws exposed. Remove (2)
Phillips screws above the radio opening.
Unclip the radio trim bezel. Remove (4)
Phillips screws from the factory head unit
and disconnect the wiring.
Locate the corner of each lower mounting
tab on the Mounting Brackets ("A").
Using the corner of each mounting tab as a
guide, cut and remove the ends of the
cupholder mounts from the Mounting
Brackets ("B").
NISSAN Altima 1998-01
1 2
3
2
Align the OUTER holes in the Mounting
Brackets Radio with the holes in the
Housing and mount with (6) #6 Self-
tapping Screws supplied. (The Brackets
will mount on an angle). Skip to the
Installation Instructions for ALL VEHICLES
on Page #3.
4
"A"
"B"
Produktspecifikationer
| Varumärke: | Metra |
| Kategori: | Inte kategoriserad |
| Modell: | 99-7413 |
Behöver du hjälp?
Om du behöver hjälp med Metra 99-7413 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Metra Manualer
3 April 2025
3 April 2025
3 April 2025
12 Mars 2025
24 Februari 2025
24 Februari 2025
14 Januari 2025
14 Januari 2025
2 Januari 2025
2 Januari 2025
Inte kategoriserad Manualer
- Eller
- SurgeX
- Rapoo
- Ergotron
- WARN
- Wet Sounds
- Lumel
- Bbf
- Sonicsmith
- Pawa
- Robern
- EQ Acoustics
- Yealink
- Bearware
- Furuno
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025