Monacor KP70-400 Bruksanvisning
Monacor
Inte kategoriserad
KP70-400
Läs gratis den bruksanvisning för Monacor KP70-400 (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 14 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 7.5 recensioner. Har du en fråga om Monacor KP70-400 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
Manufactured by :
CRC Industries Europe BVBA
Touwslagerstraat 1 – 9240 Zele – Belgium
Tel (32) (0) 52/45.60.11 Fax (32) (0) 52/45.00.34
www.crcind.com
TECHNICAL DATA SHEET
1/3
PLASTIK 70
Ref. : 20743
1. GENERAL DESCRIPTION
Quick drying, colorless transparent insulating and protective coating based on acrylic resins.
2. FEATURES
• PLASTIK 70 is a low viscosity, solvent drying acrylic based conformal coating with
excellent insulating properties. The lacquer is colorless transparent and elastic. It has a
durable adhesion in the temperature range from –40°C to +60°C and can be used for a
short period of time up to +100°C maximum. It protects printed circuit boards and
surfaces from humid inorganic-acid or caustic vapors.
• PLASTIK 70 is colorless-transparent and as such is not visual on the printed circuit board
surface.
• Contains “moisture warning”: To avoid involuntary encapsulations of moisture, Plastik 70
will warn you when applied on a humid surface, by showing a frosted, mat appearance.
• For repair works PLASTIK 70 can be soldered through or be totally removed with
acetone, THINNER FOR PLASTIK 70.
3. APPLICATIONS
PLASTIK 70 was specially developed to protect printed circuit boards. It overcomes electrical
leakages and short circuits.
As a low viscosity xing and insulating lacquer, PLASTIK 70 can also be used as extra/after
insulation of coils and transformers and overcomes disturbing noises.
PLASTIK 70 can also be used as a universal protective coating on any surface like metal,
paper, ornaments, paintings, furniture, etc.
4. DIRECTIONS
• For small runs and service applications, the easiest way to apply PLASTIK 70 is from an
aerosol can. Spray from a distance of 20 to 30 cm on the dry and degreased surface. As
pre-cleaning of PCB’s, we do recommend the use of KONTAKT PCC to remove greases,
dirt and ux residues. When nished spraying, clean the aerosol valve by turning the can
upside down and pressing the button until only propellant escapes.
• For serial production runs, PLASTIK 70 in bulk can be applied by brush or by dipping. For
spraying, two parts per volume PLASTIK 70 is diluted with up to one part of THINNER
FOR PLASTIK 70. The precise mixing ratio must be determined by trials with the
equipment concerned.
• For dip coating it is also necessary to x the immersion time and the withdrawal speed.
The faster the removal from the bulk, then thicker the lm will be. Dipping baths have to
be carefully protected to ensure no entrapment of conductive stuck-on residues.
Produktspecifikationer
| Varumärke: | Monacor |
| Kategori: | Inte kategoriserad |
| Modell: | KP70-400 |
Behöver du hjälp?
Om du behöver hjälp med Monacor KP70-400 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Monacor Manualer
25 September 2024
14 September 2024
7 September 2024
7 September 2024
7 September 2024
7 September 2024
6 September 2024
6 September 2024
5 September 2024
4 September 2024
Inte kategoriserad Manualer
- Nanlite
- Lancom
- SuperFish
- Crock-Pot
- Musical Fidelity
- Gustard
- Maglite
- Acros
- Technisat
- Heatit
- Carson
- Nvidia
- Levoit
- BERTSCHAT
- Showtec
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025