Mosconi Gladen Pro 4/10 Bruksanvisning
Läs gratis den bruksanvisning för Mosconi Gladen Pro 4/10 (1 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 13 recensioner. Har du en fråga om Mosconi Gladen Pro 4/10 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
PRO 4|10
4-channel AB class amplifier [ Rev. 3.0 – 2017/09 ]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CEA-2006-A SPECIFICATIONS
POWER RATING: 120 Watt per channel @ 4 Ohm < 1% THD+N
SN RATIO: >74 dBA / >95 dBA (DDSP) [reference: 1 Watt into 4 Ohm]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
MOS SPECIFICATIONS (Tcase = 25 °C / 4 Ohm stereo / 0.2V input level @ 14.4 Volt if not otherwise specified)
TARGET POWERs: 120 Watt per channel @ 4 Ohm Typical application:
160 Watt per channel @ 2 Ohm 106x2 + 386x1 (CH1/2 @ 4 Ohm/ST + CH3/4 @ 4 Ohm/BTL)
320 Watt BTL mode @ 4 Ohm
EFFECTIVE POWERs: 121 Watt (92 Watt @12V6) x 4 52.7 A (η = xx.x %) @ 4 Ohm / ST mode / 1% THD / 1KHz
167 Watt (127 Watt @12V6) x 4 88.0 A (η = xx.x %) @ 2 Ohm / ST mode / 1% THD / 1KHz
334 Watt (254 Watt @12V6) x 2 88.0 A (η = xx.x %) @ 4 Ohm / BTL mode / 1% THD / 1KHz
THD @ 4 Ohm / ST mode:< 0.035 % (1KHz)
THD @ 2 Ohm / ST mode:< 0.04 % (1KHz)
DIM @ 4 Ohm / ST mode:< ---- % (Power rating ref)
DIM @ 2 Ohm / ST mode: < ---- % (Power rating ref)
DC-DC converter typology / Conversion frequency: Unregulated Push-Pull / 50 KHz (± 6 %)
Supply voltage range operation: 10 V ÷ 16 V 11 V ÷ 14.4 V (Absolute maximum) / (Recommended)
Power-on/Power-off Voltage Threshold: 9 V / 7.5 V
Mute delay time: 4 secs.
Secondary voltages (VDD / DRIVE / SERV): ±38.2 V / ±12.5 V / ±13.3 V
Max output offset voltage (each channel): ±15 mV
Standby current: < 1 mA (typical)
Quiescent consumption @ 12V6 / 14V4: 0.52 A / 0.59 A (no idle current regutation)
Idle current regulation (no signal): 0.15 A (each channel)
Quiescent consumption @ 14V4: 0.89 A (with idle current setted)
Thermal protection consumption: 140 mA
Ground decoupling: (RCA Input) / 47R 1 KOhm (battery vs secondary) / (body vs battery)68 Ohm
Bandwidth (-3dB ÷ 1 Watt): < 5 Hz ÷ 135 KHz
Input sensitivity (Power rating ref): 0.35 V ÷ 12 V (5.3 V in DDSP mode)
Input impedance @ 1 KHz (STEREO input): 15 KOhm / 47 Ohm (LL) (HL)
S/N ratio (with AP filter) – Power rating ref: (filter: 10 Hz - 500 KHz )/ (filter: 10 Hz - 22 KHz “A” weighted) 81 dB 94 dB
S/N ratio DDSP (with AP filter) – Power rating ref: (filter: 10 Hz - 500 KHz )/ 89 dB 116 dB (filter: 10 Hz - 22 KHz “A” weighted)
Eq. Input noise (with AP filter): (filter: 10 Hz - 500 KHz )/ (filter: 10 Hz - 22 KHz “A” weighted)31.9 uV 6.44 uV
Channel separation@ 100Hz / 1KHz / 10KHz – 10 Watt ref: 58 dB / 56 dB / 45 dB
Xover functions (selectable filters): CH1/2= HP: 43 ÷ 500Hz(x1) or 430 ÷ 5000Hz(x10) [12 dB/oct – Q: 0.7]
CH3/4= HP: 50 ÷ 200Hz & LP:(430 ÷ 5000Hz) [12 dB/oct – Q: 0.7]
Special features: DDSP - Direct DSP (bypass all the preamplifier circuitry but the differential input interface)
HL/LL - High Level / Low Level selectable input
Controlled via uC – Internally controlled via Atmel Processor
Thermal cutoff Threshold: 95 °C (±5°C)
ProSPEED® Fan Controller Threshold: 50°C (±5°C)
Damping factor @ 100 Hz - 10 Watt ref: 453 / 396 219 / 374 [CH1/2] - [CH3/4]
Damping factor @ 1 KHz - 10 Watt ref: 455 / 398 220 / 399 [CH1/2] - [CH3/4]
Damping factor @ 10 KHz - 10 Watt ref: 199 / 245 94 / 246 [CH1/2] - [CH3/4]
Output impedance @ 1 KHz - 10 Watt ref: 8.8 mOhm / 10.1 mOhm 18.2 mOhm / 10.0 mOhm [CH1/2] - [CH1/2]
Load drive limitations (*): 2 Ohm / 4 Ohm (Stereo / Bridged)
Suggested fuse: 80 A (Internal)
Size (mm): 235 / 205 / 55
Weight (Kg): 2,4
(*) VERY IMPORTANT NOTE - READ CAREFULLY
4 Ohm ST 8 Ohm BTL or – CONTINUOUS SINEWAVE SIGNAL – pure resistive load or speaker load
2 Ohm ST 4 Ohm BTL or – – pure resistive load or speaker loadMUSICAL SIGNAL
All Right Reserved - Features may change without notice -
Produktspecifikationer
| Varumärke: | Mosconi |
| Kategori: | mottagare |
| Modell: | Gladen Pro 4/10 |
Behöver du hjälp?
Om du behöver hjälp med Mosconi Gladen Pro 4/10 ställ en fråga nedan och andra användare kommer att svara dig
mottagare Mosconi Manualer
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
mottagare Manualer
- Maxview
- ANKARO
- Inovonics
- Hager
- Cabasse
- Cambridge
- Jamo
- LYYT
- Pharos
- CAD Audio
- Audizio
- GOgroove
- Sony
- CYP
- Terratec
Nyaste mottagare Manualer
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025