Netgear GS108LP Bruksanvisning

Netgear Växla GS108LP

Läs gratis den bruksanvisning för Netgear GS108LP (2 sidor) i kategorin Växla. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 3.9 stjärnor baserat på 2.5 recensioner. Har du en fråga om Netgear GS108LP eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Installation Guide

April 2018

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

8-Port PoE/PoE+ Gigabit Unmanaged Switch

GS108LP and GS108PP

GS108LP

GS108PP

Package Contents

• Switch

• Power adapter

• Power cord (varies by region)

• Wall installation kit

• Rubber feet

• Rack-mount kit

• Installation guide

Step 1. Connect the equipment.

Step 2. Connect to power.

GS108LP

switch

Sample connections

Router

Internet

PoE+ security cameras

PoE+ access points

PoE VoIP phone

LED Status

PoE Considerations

The switch prioritizes the PoE and PoE+ power that it supplies in ascending port

order (from port 1 to port 8), with a total power budget of 120 watts. If the power

requirements for the attached powered devices (PDs) exceed the total power

budget of the switch, the PD on the highest-numbered port is disabled to make

sure that the PDs that are connected to the higher-priority, lower-numbered ports

are supported rst.

Just because a PD is listed as an 802.3at PoE powered device does not

necessarily mean that it requires the maximum power limit of the specication.

Many PDs require less power, allowing all eight PoE ports to be active

simultaneously.

The following table describes the PoE classes and switch allocations.

Device

Class

Standard Class

Description

Minimum Power

Allocated to the

Powered Device

Range of Power

Delivered to the

Powered Device

0 PoE and PoE+ Default

power (full)

0.44W 0.44W–12.95W

1 PoE and PoE+ Very low

power

4.0W 0.44W–3.84W

2 PoE and PoE+ Low power 7.0W 3.84W–6.49W

3 PoE and PoE+ Mid power 15.4W 6.49W–12.95W

4 PoE+ only High power 30.0W 12.95W–25.5W

Power LED Left Port LEDs Right PoE LEDs

1000 Mbps link

PoE in use

Off

100 or 10 Mbps link

PoE halted (see PoE

Troubleshooting)

Activity (blinking)

No PoE use (off)

No link (off)

PoE Max LED

The maximum PoE power that the switch can deliver to all attached powered devices

(PDs) is 120 watts total, with a maximum power to each port of 30 watts. (For more

information, see PoE Considerations.)

The PoE Max LED indicates the status of the PoE power that the switch can deliver to

all attached PDs, as follows:

Solid amber. Less than 7W of PoE power is available on the switch.

Blinking amber. The PoE Max LED was lit solid in the previous two minutes.

Sufcient (more than 7W of) PoE power is available on the switch (the LED is

off).

NETGEAR INTL LTD

Building 3, University Technology Centre

Curraheen Road, Cork, Ireland

Logo are trademarks of NETGEAR, Inc. Any

non-NETGEAR trademarks are used for

reference purposes only.

Get the Free NETGEAR Insight App

You can use the NETGEAR Insight app to register your switch.

1. Download the NETGEAR Insight app from your iOS or Android mobile

device.

2. Connect your mobile device to the WiFi network of the router or access

point.

3. Open the NETGEAR Insight app to log in or create an account.

4. Scan the bar code or enter the serial number of the switch located on the

product label or product packaging.

For information about how to connect a NETGEAR Insight managed switch to an

existing network, visit kb.netgear.com/000044341.

Support

Thank you for purchasing this NETGEAR product. You can visit

www.netgear.com/support to register your product, get help, access the latest

downloads and user manuals, and join our community. We recommend that you

use only ofcial NETGEAR support resources.

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en

français canadien à http://downloadcenter.netgear.com/other/.

(If this product is sold in Canada, you can access this document in Canadian

French at http://downloadcenter.netgear.com/other/.)

For the current EU Declaration of Conformity, visit

http://kb.netgear.com/11621.

For regulatory compliance information, visit

http://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

Attach the Switch to a Wall

To attach the switch to a wall, you need the wall-mount screws that are supplied

with the switch.

To attach the switch to a wall:

1. Locate the two mount holes on the bottom panel of the switch.

2. Mark and drill two mounting holes in the wall where you want to mount the

switch.

The two mounting holes must be at a precise distance of 4.27 in. (108.4 mm)

from each other.

3. Insert the supplied anchors into the wall and tighten the supplied screws with

a No. 2 Phillips screwdriver.

Leave about 0.125 in. (4 mm) of each screw protruding from the wall so that

you can insert the screws into the holes on the bottom panel.

Install the Switch in a Rack

To install the switch in a rack, you need the rack-mount brackets and screws that

are supplied with the switch.

To install the switch in a rack:

1. Attach the supplied mounting brackets to the side of the switch.

Insert the screws provided in the product package through each bracket and

into the bracket mounting holes in the switch.

2. Tighten the screws with a No. 2 Phillips screwdriver to secure each bracket.

3. Align the mounting holes in the brackets with the holes in the rack, and insert

two pan-head screws with nylon washers through each bracket and into the

rack.

4. Tighten the screws with a No. 2 Phillips screwdriver to secure mounting

brackets to the rack.

PoE Troubleshooting

Here are some tips for correcting PoE problems that might occur:

• Make sure that the PoE Max LED is off. If the PoE Max LED is solid amber,

disconnect one or more PoE devices to prevent PoE oversubscription. Start

by disconnecting the device from the highest-numbered port.

• Make sure that the Ethernet cables are plugged in correctly. For each

powered device (PD) that is connected to the switch, the corresponding right

port LED on the switch lights solid green. If the right port LED lights solid

amber, a PoE fault occurred and PoE halted because of one of the conditions

that are listed in the following table.

PoE Fault Condition Possible Solution

A PoE-related short circuit occurred on

the port.

The problem is most likely with the

attached PD. Check the condition of the

PD or restart the PD by disconnecting and

reconnecting the PD.

The PoE power demand of the PD

exceeded the maximum level that the

switch permits, which is 30.9W.

The PoE current on the port exceeded the

classication limit of the PD.

The PoE voltage of the port is outside the

range that the switch permits.

Restart the switch to see if the condition

resolves itself.

Cables and Speeds

The following table describes the network cables that you can use for the switch

connections and the speeds that these cables can support, up to 328 feet (100

meters).

Speed Cable Type

100 Mbps Category 5 (Cat 5) or higher

1 Gbps Category 5e (Cat 5e) or higher

Specications

Specication Description

Network interfaces 8 Gigabit Ethernet RJ-45 ports that support 1G, 100 M, and 10 M

8 PoE/PoE+ ports

Power adapter input Power cord varies by region.

Power adapter

output

The switch supports three power adapters:

• 130W: 54V @ 2.4A (included with the GS108PP switch)

• 90W: 54V @ 1.66A

• 67.5W: 54V @ 1.25A (included with the GS108LP switch)

Max PoE budget The maximum budget for each power adapter is as follows:

• 130W: 120W PoE (default for the GS108PP switch)

• 90W: 83W PoE

• 67.5W: 60.5W PoE budget (default for the GS108LP switch)

Dimensions

(W x D x H)

9.3 x 4.0 x 1 in. (236 x 102 x 27 mm)

Weight 1.32 lb (0.6 kg)

Operating

temperature

32–104°F (0–40°C)

Operating humidity 10%–90% relative humidity, noncondensing

Compliance FCC class A, CB, CE class A, VCCI class A, RCM class A, KC, BSMI,

EAC

Produktspecifikationer

Varumärke:	Netgear
Kategori:	Växla
Modell:	GS108LP
Vikt:	600 g
Bredd:	236 mm
Djup:	102 mm
Höjd:	27 mm
LED-indikatorer:	Ja
Strömförbrukning (max):	130 W
Rackmontering:	Ja
Medeltid mellan fel (MTBF):	2752476 h
Buffertstorlek:	192 KB
Produktens färg:	Black, Grey
Monteringsbar på väggen:	Ja
Formfaktor:	1U
Datahastighet för Ethernet-LAN:	10,100,1000 Mbit/s
Strömförsörjning via Ethernet (PoE) stöd:	Ja
Strömförbrukning (vanlig):	67.5 W
Total Power over Ethernet (PoE)-budget:	60 W
Temperatur vid drift:	0 - 40 ° C
Temperaturintervall (förvaring):	-20 - 70 ° C
Intervall för relativ operativ luftfuktighet:	0 - 90 %
Fuktighet (förvaring):	0 - 95 %
Strömkälla:	DC/PoE
Kommunikationsstandarder:	IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Stöd för garanterad tjänstekvalitet (QoS):	Ja
Plug & Play-kompatibel:	Ja
Harmonized System (HS)-kod:	85176990
Ingående ström:	1.25 A
Adresstabellstorlek:	4000 poster
Jumbo Frames stöd:	Ja
Switch kapacitet:	16 Gbit/s
10G stöd:	Nej
Flödeskontroll:	Ja
Typ av grundläggande RJ-45 Ethernet-portar:	Gigabit Ethernet (10/100/1000)
Värmeavgivning:	230.85 BTU/h
Antal Power over Ethernet plus (PoE +)-portar:	8
Antal fläktar:	0 fläkt/-ar
Switch typ:	Ohanterad
Lagra-och-vidarebefordra:	Ja
Strömanslutning:	AC-ingångskontakt
Antal Gigabit Ethernet (koppar)-portar:	8
Altitud vid drift:	0 - 1000 m
Likströmsdriftspänning:	54 V
Vidarebefordran av paket:	Ja