NodOn Micro Bruksanvisning

NodOn Inte kategoriserad Micro

Läs gratis den bruksanvisning för NodOn Micro (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 4.0 stjärnor baserat på 11 recensioner. Har du en fråga om NodOn Micro eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/3

“Factory Reset”

To perform a factory reset, press on the Micro Smart Plug button

during 5 seconds until the LED becomes orange. Release the

button, the LED will blink red/green.

Factory Reset clears the Micro Smart Plug’s memory and set

parameters to their default value.

Warning : Please use this procedure only when the primary controller is missing or otherwise

inoperable.

Resetting the Micro Smart Plug does not mean it has been removed from Z-Wave® network

controller’s memory.

Use the primary controller to remove the Micro Smart Plug from its Z-Wave® network (follow

“EXCLUSION” procedures below), before doing a Factory Reset.

INCLUSION PROCEDURE

To add the Micro Smart Plug into a Z-Wave® network:

1Plug the Micro Smart Plug.

2Put the Micro Smart Plug in “Learning mode”.

3Within 30 seconds put the Z-Wave® Controller in

“Learning mode” (See the Controller user guide for its

own Inclusion procedure).

The Micro Smart Plug will conrm the success of the Inclusion

procedure by blinking its LED in Green.

EXCLUSION PROCEDURE

To remove the Micro Smart Plug from a Z-Wave® network:

1Make sure the Micro Smart Plug is plugged.

2Put the Micro Smart Plug in “Learning mode”.

3Within 30 seconds put the Z-Wave® Controller in

“Learning mode” (See the Controller user guide for its

own Exclusion procedure).

The Micro Smart Plug will conrm the success of the Exclusion

procedure by blinking its LED in Red.

METERING

Micro Smart Plug is able to measure the amount of electric energy

consumed by the load plugged on it. This function is able to return

the power in Watt (W) and the cumulative energy in Watt-hour (Wh)

consumed since the product was installed or since the last reset.

This energy and power reports are accessible through your

gateway’s interface.

ASSOCIATION GROUPS

Using association group, the Micro Smart Plug is able to command

or notify another device of a Z-Wave ® network.

The association groups are set by the Main Controller. Once set,

the association groups allow direct control, between Micro Smart

Plug and associated devices, without involving the Main Controller

in the communication.

The NodOn® Micro Smart Plug proposes 6 association groups:

Group Group Name

1 Lifeline

2 Follow State

3 Follow Complementary State

4 Metering - High Threshold - Set

On/Off

5 Metering - Low Threshold - Set On/Off

6 Metering - Report

Group 1 – Lifeline

Maximum number of devices in group: 5

This group is generally used to report information of the Micro

Smart Plug to the Main Controller of the network.

Group 2 – Follow State

Maximum number of devices in group: 5

When the Micro Smart Plug is switched ON (respectively OFF)

using the local button, it will send ON (respectively OFF) command

to the associated devices. No command is sent if the Micro Smart

Plug is switched ON or OFF wirelessly.

This group is congurable through the parameter 3.

Group 3 – Follow Complementary State

Maximum number of devices in group: 5

When the Micro Smart Plug is switched ON (respectively OFF)

using the local button, it will send OFF (respectively ON) command

to the associated devices. No command is sent if the Micro Smart

Plug is switched ON or OFF wirelessly.

This group is congurable through the parameter 3.

Group 4 - Metering - High Threshold - Set On/Off

Maximum number of devices in group: 5

When the Micro Smart Plug reaches over the high threshold of

power dened by the conguration parameter, it will send OFF or

ON command to the associated devices.

This group is congurable through the parameter 25 and 27.

Group 5 - Metering - Low Threshold - Set On/Off

Maximum number of devices in group: 5

When the Micro Smart Plug reaches below the low threshold of

power dened by the conguration parameter, it will send OFF or

ON command to the associated devices.

This group is congurable through the parameters 26 and 27.

Group 6 - Metering - Report

Maximum number of devices in group: 5

All the meter reports and notications triggered by Metering

parameters will be reported to the devices present in this group.

This group is congurable through the parameters 21, 22, 23 and

24.

CONFIGURATION

The Micro Smart Plug NodOn® offers a wide range of

congurations, which can be set and handled by the Z-Wave®

network Main Controller.

Default State

Parameter Number Default Value Size

1 2 1 [byte]

This parameter denes the status of the Micro Smart Plug after a power outage

or after being plugged.

Value Description

0 OFF

1 ON

2 Status before power outage

Follow State

Parameter Number Default Value Size

3 3 1 [byte]

This parameter allows to enable or disable Group 2 & Group 3.

Value Description

0 Group 2 & Group 3 disable

1 Group 2 enable

2 Group 3 enable

The value may be the sum of available values.

For example, if you want to enable Group 2 & 3, the parameter

value is 1+2=3.

Always On

Parameter Number Default Value Size

4 0 1 [byte]

This parameter forces the Micro Smart Plug status to be ON. While enable it is

not possible to switch OFF the plug (local or wireless).

Value Description

0 Always ON disable

1 Always ON enable

Power Auto-Sending Report

Parameter Number Default Value Size

21 10 1 [byte]

This parameter will send a power report automatically if the power value

changes of x % W (Watt) compared to the last report.

Value Description

0 Power Auto-Polling Report Disable

1 (to 100) Power Auto-Polling Report Enable

if 1% (to100%) variation

Micro Smart Plug Type E

Reference: MSP-3-1-01

Micro Smart Plug Schuko

Reference: MSP-3-1-11

Power supply: 230V AC +/-10% - 50Hz

Self-consumption <1W

Max. power: 1800W continuous (Resistive load)

Radio frequency: 868MHz

Range up to 80 meters outdoor

Range up to 40 meters indoor

Operational temperature: -10°C / 50°C

IP20

Radio protocol: Z-Wave Plus® (500 series)

Dimensions: 46mm (Diameter) x 74mm (H)

Weight: 67g

Warranty: 2 years

USER GUIDE

MICRO SMART PLUG

The NodOn® Micro Smart Plug allows to control (Power ON or

Power OFF) an electrical appliance plugged on it: bedside lamp,

electrical heater, coffee machine, etc.

The NodOn® Micro Smart Plug is compatible with the worldwide

Home Automation standard, Z-Wave®, and all the products

Z-Wave® or Z-Wave Plus® certied from other manufacturers and/

or other applications. All non-battery operated nodes within the

network will act as repeaters regardless of vendor to increase

reliability of the network.

INSTALLATION

1Plug the NodOn® Micro Smart Plug on your power

outlet.

2Plug the electrical appliance, you want to control, on

the NodOn® Micro Smart Plug.

3The Micro Smart Plug allows to switch ON (Power ON)

or switch OFF (Power OFF) the device you want to control.

Switching ON or OFF can be done through the Micro Smart Plug

local button, or any kind of Z-Wave® compatible devices, such as

the NodOn® Octan Remote, the NodOn® Soft Remote or a Home

Automation Gateway.

If the electrical appliance (ex.: bedside lamp) has an ON/OFF button, make sure it’s positioned

on “ON”, in order that the power ON of the Micro Smart Plug will switch ON the lamp.

MICRO SMART PLUG MODES

“Local Control”

The Micro Smart Plug can be switched ON or OFF locally, through

a short press on the local button. By default, the Micro Smart Plug

is switched ON when the LED is green, OFF when the LED is OFF.

“Learning Mode”

Press on the Micro Smart Plug button during 2 seconds until the

LED becomes red. Release the button, the LED will then glow in red.

The Micro Smart Plug is in “Learning mode”.To add or to remove

the Micro Smart Plug from a Z-Wave®

network, follow “INCLUSION”

or “EXCLUSION” procedures below.

If the Micro Smart Plug is not added or removed from a network

within 30 seconds (or if the button is pushed during learning

mode), the Micro Smart Plug will automatically exit learning mode.

Expert remark: NodOn® created a power ecient « Learning

mode ». During this mode, the Micro Smart Plug will send its

« Node Information » (NIF) at regular interval.

If the Primary Controller is battery powered (such as the NodOn

® Octan Remote), rst put

the Micro Smart Plug in “Learning mode”, and then proceed to the INCLUSION/EXCLUSION

procedure of your controller.

To send a single NIF, just triple press on the Micro Smart Plug’s button.

LED state Smart Plug State

Shine Red Learning mode activated

Blink in Green Successful Inclusion

Blink in Red Successful Exclusion

Blink in Orange “Learning mode” Timeout

OFF

<1 s

2 s {Shining}

Produktspecifikationer

Varumärke:	NodOn
Kategori:	Inte kategoriserad
Modell:	Micro
Färg på produkten:	Black, Grey
Vikt:	8700 g
Bredd:	320 mm
Djup:	390 mm
Höjd:	1220 mm
Ljudnivå:	80 dB
Årlig-energiförbrukning:	37.8 kWu
Luftfiltrering av dammsugare:	HEPA
Smutsavskiljningsmetod:	Filtrerend
Dammkapacitet:	5.5 l
Maximal ineffekt:	850 W
Typ av dammsugare:	Stofzak
Rengör ytor:	Tapijt
Luftflöde:	43 l/s
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 - 60 Hz
Standard nominell bredd:	- mm
Arbetsbredd (standardborste):	380 mm
Turbinkraft:	850 W