PAC MCI-FD22 Bruksanvisning
PAC
Inte kategoriserad
MCI-FD22
Läs gratis den bruksanvisning för PAC MCI-FD22 (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 22 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 11.5 recensioner. Har du en fråga om PAC MCI-FD22 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
Multi Camera Input Interface
for Select Ford Vehicles
MCI-FD22
© 2017 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev. 070617
The MCI-FD22 will allow the addition of front, and blind spot cameras, in vehicles equipped with the 4.2” screen and a
factory reverse camera. The MCI-FD22 has multiple user proles that can be set using the DIP switches or by PC app.
The MCI-FD22 also has on-demand activation of rear or front camera.
Introduction & Features
Important Notes
1. Only compatible in vehicles equipped with the 4.2” screen and a factory reverse camera.
2. The accessory output is rated at 10A of current. If more current is needed an external relay must be used.
3. All DIP switches must remain in the off (up) position in order to set up the MCI with the app.
DIP switches Blind Spot Camera Operation Front Camera Operation
All Off (up) PC Setup PC Setup
1 on On with Turn Signal Off
2 on On with Turn Signal On with Shift to Drive, then Off with MPH > 6 MPH or 30s
1,2 on
On with Turn Signal and MPH
> 0
Off
3 on
On with Turn Signal and MPH
> 0
On with Shift to Drive, then Off with MPH > 6 MPH or 30s
1,3 on
On with Turn Signal and MPH
> 20
Off
2,3 on
On with Turn Signal and MPH
> 20
On with Shift to Drive, then Off with MPH > 6 MPH or 30s
1,2,3 on Double Tap Turn Signal Off
4 on Double Tap Turn Signal On with Shift to Drive, then Off with MPH > 6 MPH or 30s
2,3,4 on On with Shift to Drive, then Off with MPH > 6 MPH or 30sOff
All On (down) Off Off
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
***All DIP switches must remain in the off (up) position in order to set up the MCI with the PC
Installation
Module Layout
LED 1
LED 2
Interface
Connector 1
Expansion Port
(For VS41 Connection)
Interface Connector 2
Reset Button
USB Port
(For Firmware
Updates)
Feature Select
DIP switches
Produktspecifikationer
| Varumärke: | PAC |
| Kategori: | Inte kategoriserad |
| Modell: | MCI-FD22 |
Behöver du hjälp?
Om du behöver hjälp med PAC MCI-FD22 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad PAC Manualer
10 Mars 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
12 Februari 2025
12 Februari 2025
Inte kategoriserad Manualer
- Alga
- MOZOS
- Eheim
- Learning Resources
- X-Rite
- W'eau
- Dreambaby
- Turbo Scrub
- Varytec
- BrightSign
- Burris
- BabyGO
- XTRARM
- Bluebird
- Nevir
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025