Peerless PS200 Bruksanvisning
Peerless
Inte kategoriserad
PS200
Läs gratis den bruksanvisning för Peerless PS200 (21 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 8.5 recensioner. Har du en fråga om Peerless PS200 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/21
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 06-08-07 SHEET #: 083-9004-4 05-25-10
Installation and Assembly:
Paramount™ A/V Component Shelf
Model: PS200
Maximum UL Load Capacity:
100 lb (45.4 kg)
This product is intended for use with UL
Listed products and must be installed by a
qualifi ed professional installer.
2 of 21 ISSUED: 06-08-07 SHEET #: 083-9004-4 05-25-10
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• stud fi nder ("edge to edge" stud fi nder is recommended)
• phillips screwdriver
• drill
• 5/16" bit for concrete and cinder block wall
• 1/2" bit for metal stud wall
• 5/32" bit for wood stud wall
• level
For customer care call (800) 865-2112 or (708) 865-8870.
Accessories (sold separately)
• 2 piece Metal Stud Fastener Kit (ACC 215) (Metal Stud
not evaluated by UL)
• Safety Belt (ACC 322)
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall ................................................................................................................................................4
Installation to Solid Concrete or Cinder Block ........................................................................................................................5
Installing Support Arms and Wall Plate Cover ........................................................................................................................6
Installing Safety Belt (ACC 322 sold separately) ....................................................................................................................7
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud fi nder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
Wood Beam Included•
Solid Concrete Included•
Cinder Block Included•
Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit; •
(not evaluated by UL)
• Brick Contact Qualifi ed Professional (not evaluated by UL)
Other or unsure? Contact Quali• fi ed Professional
WARNING
3 of 21 ISSUED: 06-08-07 SHEET #: 083-9004-4 05-25-10
DE
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly dierent than illustrated.
A
C
B
For mounting under a surface
Measure the height of the component to be placed onto
the mount, this measurement will be referred to as .H
Determine minimum distance from surface bottom to X
mounting hole centers using the formula X = H - 0.5" or
X = H - 13 mm
Note: If height of component is less than 4.5" (114
mm), a minimum distance of 4" (102 mm) is required for
X.
For mounting above a surface locate mounting hole
centers no less than 7.25" from surface top.
X = H - 0.5"
X = H - 13 mm
H
SIDE VIEW
1
E
X
B
7.25"
(184 mm)
MINIMUM
SURFACE TOP
SURFACE BOTTOM
DVD PLAYER,
AMPLIFIER, ETC.
F
PS200
Description Qty. Part #
A
support arm 2 083-0016
Bwall plate 1 083-P1019
Cwall plate cover 1 590-1281
Dconcrete anchor 2 590-0320
E#14 x 2.5" wood screw 2 5S1-015-C03
Fsafety belt 1 083-8015
Parts List
Produktspecifikationer
| Varumärke: | Peerless |
| Kategori: | Inte kategoriserad |
| Modell: | PS200 |
Behöver du hjälp?
Om du behöver hjälp med Peerless PS200 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Peerless Manualer
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
19 September 2024
Inte kategoriserad Manualer
- Alesis
- KM-fit
- Magivaac
- Duro
- Basbau
- Hauck
- Brainstorm
- AS Synthesizers
- Namco Bandai Games
- Westcott
- Waterstone
- JANDY
- Irobot
- Radiant
- Mio
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025