Penton RCS6FT/EN Bruksanvisning
Läs gratis den bruksanvisning för Penton RCS6FT/EN (1 sidor) i kategorin högtalare. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 10.5 recensioner. Har du en fråga om Penton RCS6FT/EN eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
RoHS
Penton UK Ltd
Unit 2 Teville Industrials | Dominion Way | Worthing West Sussex | | BN14 8NW
T: +44 (0)1903 215315 F: +44(0)1903 215415 E: sales@pent onuk.co.uk | |
www.pentonuk.co.uk
1. LOUDSPEAKER
ENCLOSURE
2. REFERENCE AXIS
3. REFERENCE PLANE
4. HORIZONTAL PLANE
ROUND METAL CEILING
LOUDSPEAKERS
f RCS6FT/EN
f RCS6FT/ENC
INSTALLATION INSTRUCTIONS
EN54-24:2008
Certificate No: 0359-CPD-0120 TYPE A
Circuit Diagram
f RCS6FT/EN
f RCS6FT/ENC
* with capacitor
I IA
Slide
I ID
D
D
D
D
“C ”
“B”
1. Remove the wing nut “A” located on
the inside of the fire dome.
FITTING THE DOME INTO A CEILING
6. Cut a 200mm diameter hole paying attention to ensure that the cut-out is
accurately made. As if it is not, the speaker may not fit correctly into the ceiling
preventing the speaker from sitting flush to the surface.
7. Loosen the slider knob “D”, push the knob & plate upwards to the top of the fire
dome and re-tighten the knob to hold the slider in place. Repeat the same process
with the other slider.
8. Push the complete fire dome into the cut-out.
9. Once in place loosen the slider knob “D”, push the knob & plate downwards
until the slider makes firm contact with the ceiling. Tighten the knob to secure it into
place. Repeat the same process with the other slider.
10. The fire dome should be firmly
secured into the ceiling.
11. Take the speaker and
compress one of the mounting springs
& place both ends of the spring into
one of the retaining brackets located
on the inside wall of the fire dome.
Release the spring slowly into the
bracket. Once fully released the
spring will hold one side of the
speaker into the fire dome.
12. With the speaker in this position
connect the 3 wires hanging from the
termination plate on to the speaker using
the spade terminals provided.
13. Fit the second spring mount on
the speaker to the remaining bracket on
the inside of the fire dome. Finally push
the speaker into position.
14. If fitted correctly the speaker
should fit flush to the surface.
2. Lift the termination plate upwards
& away to separate it from the fire
dome “B”.
3. Gland the installation cable into the termination plate using
suitably rated 20mm glands. 2 gland entries are provided for
“loop in” “loop out” termination if required.
4. Terminate the installation cable into the terminal block on
the underside of the termination plate “C”.
5. Fix the termination plate back into the fire dome and secure
using the wing nut previously removed. Do not over tighten to
avoid damaging the thread.
4
3
2
1
EN54-24
ZCL0504-058/059
OCTOBER 2011
COMMON
*
6W
3W
1.5W
0.75W
0.25W
Produktspecifikationer
| Varumärke: | Penton |
| Kategori: | högtalare |
| Modell: | RCS6FT/EN |
Behöver du hjälp?
Om du behöver hjälp med Penton RCS6FT/EN ställ en fråga nedan och andra användare kommer att svara dig
högtalare Penton Manualer
15 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
högtalare Manualer
- Schaub Lorenz
- Dual
- RCA
- Porter-Cable
- Meinl
- EVOLVEO
- Atlas Sound
- Moki
- T'nB
- Speakal
- Emphasys
- Peaq
- SuperTooth
- NAD
- Micca
Nyaste högtalare Manualer
23 Oktober 2025
20 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
18 Oktober 2025