Petsafe PPA19-16732 Bruksanvisning
Petsafe
ej kategoriserat
PPA19-16732
Läs gratis den bruksanvisning för Petsafe PPA19-16732 (12 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 2.5 recensioner. Har du en fråga om Petsafe PPA19-16732 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/12
Quick Start Guide
Pika-aloitusopas
Snabbstartsguide
Hurtigveiledning
Lynvejledning
Manual-Locking Cat Flap
Kattlucka med manuell låsning
Manuaalisesti lukittava kissanluukku
Katteluke med manuell lås
Manuel kattelem med lås
300
Series
Series
Serien
Series
Serien
Please read this entire guide before beginning.
Lue tämä opas kokonaan ennen kuin aloitat.
Läs hela handboken innan du använder apparaten.
Les hele bruksanvisningen før du starter.
Læs hele denne vejledning før brug.
2
ENFINO
SV
DA
petsafe.com
The PetSafe
™
Manual-Locking Cat Flap is suitable to fit most doors or partitions
although additional materials and competent DIY skills may be required. This cat
flap is designed to adapt easily to cut-out sizes for Staywell
™
200, 300, 400, 500,
900 and Petporte smart flap
™
series cat flaps. Some simple DIY skills are required
and minor adjustments to the cut-out or additional accessories might be needed.
Installation – Measurement and Marking
Measure the belly height of
your cat. This is usually
100 mm –150 mm (Fig. A).
Mark this measurement on the
outside of your door and draw a
straight horizontal line
168 mm long (Fig. B).
Please keep in mind that this horizontal line will eventually be the bottom of the hole
you will cut in your door. The frame of the cat flap will be 25 mm lower. If necessary,
this line may have to be raised slightly to account for some door designs.
Installation
–
Doors
1. Attach the supplied Cutting Template to the outside of your door in the correct
position, ensuring that it is the right way up and level (Fig. C).
2. Drill four (4) corner holes with a 12 mm diameter drill bit as marked on the
Cutting Template through the door (Fig. D). Please ensure that the drill remains
straight and level.
3. Using a jig or
key-hole saw, cut
along the dashed
line as indicated
on the Cutting
Template. (Fig. E).
(x)
Fig. A
(x)
Fig. B
(X)
(X)
Fig. D
(X)
Fig. C
Fig. E
4. Temporarily place both frames into the cut-out (Fig. F).
5. Level the cat flap until it is in the proper position. On the
outside, use a pencil to mark screw holes through the
holes on the exterior frame (Fig. G).
6. Remove the cat flap and drill the screw holes with a
6 mm drill (Fig. H).
7. Clean the area from any dust, dirt or debris.
8. Place the interior frame (with attached tunnel) into
the hole from the inside. Align the exterior frame to
the outside of the door. Four (4) different lengths of
screws have been provided with this cat flap. Select the
appropriate length. Using a manual screw driver, screw
the exterior frame through the holes in your door to the
interior frame (Fig. I).
9. When the installation of the cat flap is completed,
place the two (2) blanking plugs over the screws on the
exterior frame (Fig. J).
10. The cat flap is ready to use (Fig. K).
Screw Selection Guide
Cut-Out Thickness Screw Length
12 mm – 21 mm 40 mm screw
22 mm – 31 mm 50 mm screw
32 mm – 41 mm 60 mm screw
42 mm – 51 mm 70 mm screw
Fig. H
Fig. J
Fig. K
Fig. F
Fig. G
Fig. I
Produktspecifikationer
| Varumärke: | Petsafe |
| Kategori: | ej kategoriserat |
| Modell: | PPA19-16732 |
Behöver du hjälp?
Om du behöver hjälp med Petsafe PPA19-16732 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Petsafe Manualer
26 Juni 2025
26 Juni 2025
25 Juni 2025
25 Juni 2025
ej kategoriserat Manualer
- Cateye
- Mount-It!
- ESI
- Foppapedretti
- Hansgrohe
- AEG
- Schlage
- S.M.S.L
- Teslong
- ADATA
- Blow
- Clarion
- Weidmüller
- DS18
- Arturia
Nyaste ej kategoriserat Manualer
26 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025
26 Juni 2025