Plieger K12 Bruksanvisning

Plieger Termostat K12

Läs gratis den bruksanvisning för Plieger K12 (2 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 8.5 recensioner. Har du en fråga om Plieger K12 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

ENGLISH

-



The K12 is designed specially for electrical oor heang. The oor

sensor is supplied standard with the system. Always switch o the

power before installaon or removal. The connecon should always

be carried out by a qualied electrician according to the local instruc-

ons. Please study these guidelines with cauon before installaon

and use. Save these instrucons carefully for possible later use.



Check before installaon the power is o. Remove the cover and

protecon cap by carefully taking them o together.

Connect the sensor, power and power supply cables according to the

wiring diagram.

Place the thermostat in the right posion and fasten this with two

screws. Replace the cover and protecon cap by pressing them soly.

As soon as the power is turned back on 12.00 will appear ashing and

the thermostat can be used.

In case of a newly installed oor, allow at least three weeks drying out

periods.



Turn on the power aer having checked the installaon instrucons

carefully. In the screen the present room temperature and 12.00h will

appear ashing.



Le Note the signs, higher or lower

Middle SET: menu choice and conrmaon

Right Note the signs, higher or lower



At the boom appears “SET” above the middle buon and by pres-

sing this, the menu will appear.

The menu is made up from:

Day/Time Seng right day and me

Program Change standard week program

Temperature Adjustment standard seng

On/O On/O

Auto/Man Automac or manual



Seng day and me

1. Press the middle buon twice

2. First conrm Day/Time with the middle buon

3. Set the day on the top and conrm

4. Wait unl hour ashes. Set the correct hour and conrm

5. Wait unl minute ashes. Set the right minutes and conrm

Almost immediately automac will appear in the main screen.



The thermostat is now operave following to the standard program.

You can recognise this from the blinking of the two dots between the

hour and the minutes in the main screen. Please do not change this

program during the rst week so the thermostat can store historical

data. When power is consumed the word HEATING will appear on the

screen. If not the thermostat is funconing on stand-by.

In the menu the sengs you will nd underneath are pre-program-

med. These sengs can be adjusted by going into the menu by pres-

sing SET, select the relevant topic, conrming this and then adjusng

this with the le or right buon. Do not forget to conrm all steps

with the middle buon. Aer the last conrmaon the main screen

will appear again.

Incorrect sengs can be reset in the same way.



Choose Auto/Man and press the right buon for approx. 5 seconds.

 Conrm and adjust standard sengs of:

Mo to Fri from 5.00h to 9.00h and from

17.00h to 23.00h. Sa / Sun from 9.00h to 23.00h.

 Adjust comfort temperature and conrm.

Night set back will show. Adjust as below.

The dierence can be approx. 3°C for main

heang and 5°C max. for side heang. For

example: if you set a comfort temperature of 21°C

for side heang, the set back temperature should

not be lower than 16°C.

 Conrm and adjust standard seng On to O or

vice versa.

 Conrm and adjust standard seng Auto to Man

or vice versa.



When desirable a childproof lock can be installed by pressing the mid-

dle buon for approx. 8 seconds. A small lock will

appear in the top right of the screen. This lock can be turned o by

pressing the middle buon for 8 seconds.



When the following codes appear on the screen, rst contact your

supplier.

F1 = Sensor failure

F2 = Power failure

F3 = Memory failure





Choose Auto/Man in the menu and press the le buon for approx. 5

seconds. You now enter the service menu which is only intended for

the installer.

1 = With the ashing number you can adjust the screen contrast.

2 = Press SET - with the ashing number you can now adjust the

calibraon.

3 = Press SET - with the ashing number you can now adjust the dif-

ferenal.

4 = Press SET and the soware number appears on the screen.

To return to the main screen press SET



Power supply 230V / 16 Amp

Max. capacity 3200W

Temperature range 5°C to 40°C

IP-Class IP21

Colour RAL9010 – Polar/White

Warrantee 2 years

Examinaon CE

Manufacturer C&F Technics BV, The Netherlands

Document type

Document description

Document code and revision

Item

Date

DOC.file

Page

Modifier

Doc. no.

Replaces

Drawing

4.1.2012

1 / 1

-------- --

-------

2345678

5678

Picture for manual 1

Author