Prier C-108X10 Bruksanvisning

Läs gratis den bruksanvisning för Prier C-108X10 (2 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 5 recensioner. Har du en fråga om Prier C-108X10 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

PRIER Products, Inc.

4515 E 139th St.

Grandview, MO 64030

800-362-9055 Fax: 800-362-1463

www.PRIER.com

Installation, Operation & Maintenance Instructions for the

PRIER C-108/208 Diamond Series Hot and Cold Wall Hydrant

*Please leave this sheet for the property homeowner*

Thank you for purchasing the PRIER C-108/208 Diamond Series Hot and Cold Wall Hydrant, the nest quality hot and

cold wall hydrant available. Your C-108/208 will provide you years of dependable service with little or no maintenance.

Installation:

Installation procedures may vary slightly depending on the seat option purchased and the installation inlet options. PRIER

freezeless wall hydrants are available with the following inlet options:

1. Determine the location for the installation of the hydrant. The valve must be installed into a heated area of the struc-

ture that will not drop below freezing. Ensure there is adequate work room in the interior of the structure for securing

the hydrant to the plumbing piping.

2. The PRIER C-108/208 is designed for installation for either vertical or horizontal application. The hose threads must

be oriented in the DOWN position then locked into place. If the hose thread is not oriented properly, the water will not

be able to drain from the hydrant and freeze damage may occur.

3. Bore 2 holes in the size listed above at 3 1/2” centers through the wall in the desired position for the installation.

4. All freezeless wall hydrants require a slight downward pitch to aid the draining process of the hydrant once the prod-

uct is turned to the “off” position.

5. Ensure supply piping is free of debris, solder and sealants.

6. If you are planning to solder the connection (D, S or F style seats), be certain the hydrant is in the fully open position

to prevent seat damage from the heat.

7. Connect the water supply piping to the freezeless wall hydrant as desired. With a closed-end hose on the valve creat-

ing back pressure, test the installation for leakage.

8. After the water supply connection is made, secure the hydrant to the structure using appropriate screws through the

two mounting holes on the casted back ange.

Operation:

Operation of the C-108/208 Diamond Series Hot and Cold Wall Hydrant is a simple process. Water ows through the

hydrant after turning the handles (or operating key for the C-208 style) counter-clockwise to the “on” position. Turn off the

hydrant by turning the handle clockwise to the “off” position.

The hydrant will drain for a few moments. If the dripping persists after a few moments, tighten the handle slightly until the

dripping stops. Be careful not to overtighten the hydrant.

The C-108/208 incorporates a backow preventer that operates as a check valve in the rare case that water is forced

backwards into the valve. The backow preventer has been tested to 125 PSI pressure.

*ALWAYS REMOVE HOSE DURING FREEZING TEMPERATURES*

*INTENDED FOR IRRIGATION USE AND OUTDOOR WATERING*

Maintenance:

The C-108/208 Diamond Series Hot and Cold Wall Hydrant leaves the factory fully air tested and operational. It is treated

with an FDA approved lubrication. The hydrant requires no scheduled maintenance to provide long life.

D1/2” MIP x 1/2” SWT Bore 1” Hole

S1/2” SWT x 3/4” Push-On Bore 1” Hole

X1/2” Crimp PEX Bore 1” Hole

W1/2” Wirsbo

®

PEX Bore 1” Hole

T3/4” MIP x 1/2” FIP Bore 1 1/8” Hole

F3/4” MIP x 3/4” SWT Bore 1 1/8” Hole

FX3/4” Crimp PEX Bore 1 1/8” Hole

FW3/4” Wirsbo

®

PEX Bore 1 1/8” Hole

Produktspecifikationer