Pro-Ject MaiA DS3 Bruksanvisning


Läs gratis den bruksanvisning för Pro-Ject MaiA DS3 (8 sidor) i kategorin hi-fi system. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6.5 recensioner. Har du en fråga om Pro-Ject MaiA DS3 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/8
INSTRUCTIONS FOR USE
Pro-Ject MaiA DS3
© Pro-Ject Audio Systems · MaiA DS3 · Revision 12.09.2022
2
Thank you for purchasing an integrated amplifier from Pro-Ject Audio Systems.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
Safety instructions
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to connect/disconnect the unit from the mains. Make sure that the power supply
is easily accessible at all times. Never handle the device, the power supply while your hands are wet or
damp. Avoid letting liquids enter the device or the power supply. Never place any item containing
liquid, such as a flower vase on or near the device. Never spill any liquid on the device or the power
supply. Never place any naked flame sources, such as lighted candles on or near the device. The product
shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar
conditions.
Connectors
1. Make all connections except the connection the headphone and USB whilst the unit to is
disconnected from the mains.
2. Never connect or disconnect the power supply to or from the unit whilst the power supply is connected
to the mains. Never use any other power supply than the supplied one, with the exception of dedicated
Power Boxes which can replace original power supplies.
3. Take care to connect the left and right channels of RCA inputs correctly. The right channel is usually
marked red, the left channel black or white.
4 Speaker connections for the left speaker are located on the right hand side of rear view above,
.
.
.
. .
connections to right speaker are located on the left side Speaker connectors marked red represent . +
+
+
++
according indicators on speaker terminal.
Mains power connection and methods to switch the unit on and off
Connect the low voltage plug from the power supply to the Po
Po
Po
PoPower 36V D
wer 36V D
wer 36V D
wer 36V Dwer 36V DC
C
C
CC socket of the unit befor
befor
befor
beforbefore
e
e
e e
connecting the power supply to the mains. MaiA DS3 can be switched on and off by using 2 different
methods which are equal in priorities.
© Pro-Ject Audio Systems · MaiA DS3 · Revision .09.202212
3
1. Using front pushbutton to switch on to standby or in
The pushbutton on the front panel of the unit alternately turns the power on or returns it to standby mode. The
blue LED on the front panel shows that the unit is powered on. If a trigger signal is present MaiA DS3 can’t be
switched off by the pushbutton.
2. Remote power on - triggers
MaiA DS3 can be switched on via other Box Design components when a 12V trigger voltage is present at the
2.5mm socket marked Trigger
Trigger
Trigger
Trigger Trigger Input.
Input.
Input.
Input.Input. Special power-on cables (polarity ) in diverse lengths are available
as accessories. The remote power-on signal can be relayed to further units via the Trigger
Trigger
Trigger
Trigger Trigger Out
Out
Out
OutOutput
put
put
putput socket. When
the 12V trigger signal is switched off, MaiA DS3 will also switch off.
Trigger cables may only be plugged into the sockets when the amplifier is disconnected from the power
supply and from the mains. Failure to do so may result in damage of the unit.
Line o put ut
A power amplifier, active loudspeakers or an active subwoofer can be connected to the output sockets marked
Var
Var
Var
VarVar Output
Output
Output
OutputOutput .
Fix Line Output
Fix Output
Fix Output
Fix Output
Fix OutputFix Output connects an analogue record device or a headphone amplifier.
Connection to the speakers
The output terminals accept loudspeaker cables terminated with 4mm Banana plugs, spades connectors or
naked wire.
Phono input
Connect the tonearm signal lead to the Phono
Phono
Phono
PhonoPhono
input
of the amplifier. The MM/MC switch on the back panel
allows to adapt to connected cartridge type. The earthing wire may be connected to the screw terminal if you
encounter hum problems when using the turntable.
Line inputs
Line level sources (CD player, radio or TV) can be connected to the inputs marked In 2
In 2
In 2
In 2In 2,
,
,
, , 3 or I
3 or I
3 or I
3 or I 3 or In 4
n 4
n 4
n 4n 4
In
In
In
InIn .
Sources with a digital output such as TV, satellite/cable receiver or a game console can be connected to the
digital inputs. Optical to and and coaxial to
In
In
In
InIn 5
5
5
5 5 In
In
In
InIn 6
6
6
6 6 In
In
In
InIn 7
7
7
7 7
.
.
.
. .
Sub output
An active subwoofer may be connected to the output sockets marked .
Sub Out
Sub Out
Sub Out
Sub OutSub Out
Connecting to a Computer
Connect the USB-input of the MaiA DS3 (unit must be switched on) to a free USB-socket on your
In
In
In
InIn 8 USB
8 USB
8 USB
8 USB 8 USB
computer and turn it on/make sure it is powered on. Select input 8
8
8
88.
* For Windows
®
operating systems an USB Class 2 driver (supplied on CD) has to be installed
Mac OS
®
operating systems do not need an additional driver or setup.
Linux operating systems include an USB Audio Class 2 driver from Linux Kernel 2.6.35 and higher.
+


Produktspecifikationer

Varumärke: Pro-Ject
Kategori: hi-fi system
Modell: MaiA DS3

Behöver du hjälp?

Om du behöver hjälp med Pro-Ject MaiA DS3 ställ en fråga nedan och andra användare kommer att svara dig