Ring Flood/Freeze Sensor Bruksanvisning
Läs gratis den bruksanvisning för Ring Flood/Freeze Sensor (2 sidor) i kategorin bildskärm. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 1.5 recensioner. Har du en fråga om Ring Flood/Freeze Sensor eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Prevent water and ice damage
at home.
Ring Flood & Freeze Sensor is a smart
sensor for your Ring Alarm system. Place
it anywhere you want to monitor for
flooding or freezing conditions.
On the bottom of the Sensor, you’ll
see flood sensors that can tell when
water is present. Inside, a temperature
sensor keeps watch for dangerously low
temperatures (around 40 ° F or 4.4 ° C).
When either of these conditions occur,
the Ring app notifies you so you can take
care of the issue.
Contents
1. Diagram
2. In-app Setup
3. Physical Installation
4. Additional Information
Diagram
Begin the setup process near
your Ring Alarm Base Station.
To add devices to your Ring Alarm, it
must be disarmed. If your Ring Alarm is
armed, please disarm it now.
In the Ring app, tap Set Up a Device and
find Ring Flood & Freeze Sensor in the
Security Devices menu.
To complete the setup process, follow
the in-app instructions.
When prompted, scan the QR
Code or enter the PIN.
This begins the pairing process. The QR
Code and PIN are on the back of your
sensor and in the product packaging.
For Ring Alarm
When prompted, open the lid and
pull out the clear tab.
Twist the lid to the left to unlock, then lift it
to remove. Next, pull out the clear battery
tab. This turns on the Sensor.
Your Base Station finds it automatically.
1.
Say hello to
your Ring
Flood & Freeze
Sensor.
2.
Set up your
Ring Flood &
Freeze Sensor
in the Ring app.
LED Ring
Setup Button
Flood Sensors
Flood & Freeze Sensor
Watch your Sensor connect.
As your Sensor pairs to your Base Station,
its LED ring blinks slowly, then quickly.
Once the Sensor is paired, the LED glows
blue for three seconds.
Can’t scan the QR code?
No problem! In the app, on the scanning
screen, tap Not working? Enter number
instead.
Then, enter the 5-digit PIN code you’ll see
below the QR code. Next, you’ll put your
Sensor in manual pairing mode.
To do this, open the Sensor, then remove
and reinstall the battery. Finally, press the
Setup Button to begin pairing.
Place the Sensor on the ground.
Choose a spot next to a possible source
of flooding, such as your water heater,
sink, or refrigerator. Take care to place
the Sensor in a location where it won’t be
kicked or moved unintentionally.
Close the lid.
Place the lid back on the Sensor, taking
care to line up the semi-circle on the rim
of the lid with the “open” semi-circle on
the base. Twist the lid clockwise to lock
it in.
How to remove this Sensor from
your system:
Open the side menu in the Ring app and
tap Devices, then . Next, Base Station
select your Sensor, then tap the gear-
shaped icon, and tap Remove Device.
When prompted, open the sensor and
remove and reinstall the battery to
complete the removal.
Having trouble with your Sensor?
If your Flood & Freeze Sensor stops
working or can’t connect (even with a
good battery), try a factory reset.
To do this, press and hold the Setup
button for 10 seconds. When the LED
ring stops blinking, the Sensor has reset.
How to replace the battery:
Twist the lid on the Sensor counter-
clockwise and lift to remove. Replace the
battery with a fresh CR123A cell.
The Sensor then reconnects to your Ring
Base Station automatically.
LED status patterns:
For info on other LED patterns,
visit ring.com/help.
Test your Flood & Freeze Sensor.
Now that your Sensor is set up, bring it to
the area you want to monitor. To ensure
it remains connected to your Alarm Base
Station in its new location, test the Sensor.
To do this, push the Setup button inside
the Sensor. If the LED blinks blue, the
Sensor is connected and ready to place.
If it blinks red, try the test again. You may
find that repositioning the Sensor (even
just a few inches) can improve reception.
If the surface you’re placing on is not flat, tr y
to place your Sensor at the lowest point.
Blue Blink (1x)
Water or low
temperature
detected
Red Blinks (3x)
Sensor
tampered
3.
Place your Ring
Flood & Freeze
Sensor.
4.
Additional
information.
© 2019 Ring LLC or its affiliates .
RING, Always Home, and all related logos are trademarks of Ring LLC or its affiliates.
Last updated: 05/13/19
Battery
Setup
Button
If the S ensor cannot connect, try installing a
Ring Range Extender between your Sensor
and Base Station.
If the S ensor does not pair successfully,
the LED ring glows red. To try the pairing
process again, remove and reinstall the
battery inside the Sensor.
This process disconnects the Sensor from
Ring Alarm. To begin using the Sensor again ,
repeat the setup process in the Ring app.
Produktspecifikationer
| Varumärke: | Ring |
| Kategori: | bildskärm |
| Modell: | Flood/Freeze Sensor |
Behöver du hjälp?
Om du behöver hjälp med Ring Flood/Freeze Sensor ställ en fråga nedan och andra användare kommer att svara dig
bildskärm Ring Manualer
27 Juli 2025
bildskärm Manualer
- HP
- Vaxis
- QIXZOCV
- GTMEDIA
- Alienware
- BenQ
- Ag Neovo
- AVer
- Sharp
- Acer
- Titan Army
- Hannspree
- Viewsonic
- Advantech
- InFocus
Nyaste bildskärm Manualer
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
27 Juli 2025