SE Electronics guitaRF Bruksanvisning
SE Electronics
Inte kategoriserad
guitaRF
Läs gratis den bruksanvisning för SE Electronics guitaRF (5 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 14 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 7.5 recensioner. Har du en fråga om SE Electronics guitaRF eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/5
guitaRF™ ASSEMBLY + USE
guitaRF™ aS SEMBLY Ma Nua L
sE Electronics guitaRF™ Assembly + Use
Thank you for purchasing an sE Electronics guitaRF! We hope it helps
make your records and live shows sound great, and makes recording
guitars & bass (and anything else!) that much easier for you.
STEP ONE
w the vertical standoff into the
om of the lter, making sure the
side of the standoff is aligned with
back of the lter. Use the included
nch to adjust the tightening nut on
standoff (a) to make sure they’re
ned properly.
STEP TWO
Making sure the at side of the
standoff is facing the screw on the
back of the base stand, insert the
standoff (with the lter attached) into
the base, and tighten it securely in
place with one of the two included
smaller screws (b).
(b)
(a)
Alternatively, the guitaRF can be mounted
to any standard mic stand thread, 5/8” or
3/8” (with the included 3/8” adapter).
guitaRF™ aS SEMBLY Ma Nua L
sE Electronics guitaRF™ Assembly + Use
STEP THREE
Use the second of the smaller screws
(c) to tighten the vertical adjustment
rod (d) to the hardware. This screw/
rod can be used to raise or lower the
condenser or ribbon hung from the
guitaRF hardware, with (e) used to
move it towards or away from the lter.
(c)
(d)
(e)
(f)
(g)
STEP FOUR
Attach the hardware to the top of
the guitaRF with the included larger
screw (f), rubber washer on top of the
bracket, and paper washer underneath.
This screw can be used to rotate the
hardware mount relative to the lter.
STEP FIVE
Insert your dynamic or small-capsule
mic into the pass-through hole of the (g)
guitaRF. It should t snugly.
Screw your condenser or ribbon’s mic
clip (or shockmount) onto the hanging
vertical adjustment rod (d), and then use
(c) (e) (f) , and to ne-tune the position of
the hanging mic relative to the dynamic/
small-capsule mic.
Produktspecifikationer
| Varumärke: | SE Electronics |
| Kategori: | Inte kategoriserad |
| Modell: | guitaRF |
Behöver du hjälp?
Om du behöver hjälp med SE Electronics guitaRF ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad SE Electronics Manualer
10 September 2024
7 September 2024
7 September 2024
2 September 2024
2 September 2024
Inte kategoriserad Manualer
- Martin Audio
- Anywhere Cart
- Showtec
- Violectric
- Naim
- Irobot
- Tanaka
- Microair
- WAGAN
- Milan
- Kruidvat
- Gretsch
- Aquatica
- Hooker
- Stannah
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025