SEADA G88-HDMI Bruksanvisning
Läs gratis den bruksanvisning för SEADA G88-HDMI (2 sidor) i kategorin Processor. Guiden har ansetts hjälpsam av 17 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 9 recensioner. Har du en fråga om SEADA G88-HDMI eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
G88 Quick Start Manual
SD-EN-014 V01
Note
1. Do not fix the device to any surface which is a heat source to avoid over heating
2. Do not cover the surface or ventilation grills of the device to avoid over heating
1. Verify the package contents
Please verify the package contents against the List Below
1. G88 Controller x1
2. Power Cable x1
3. Software Disk x1
4. Serial Cable x1
5. Network Cable x1
6. Remote Control x1
2. Set up the G88
I. Connect the power cable to the unit and power it up
II. Connect the outputs to the screens of the video wall
III. Connect all the video sources to the inputs of the devices
Note: G88 remembers the settings used on the device before power off. The default setting for the new unit is 2x4
video wall with input 1 across the 8 screens. All outputs are set at resolution of 1920 x 1080@60.
3. Run the software on control PC
Users can run the G88H.exe software directly without installation. Software is on the disk in the package or you can
download it from the SEADA website. Double click the G88H software to get the Dialog box as below
Default password for Administrator:111111
Default password for User: 000000
Type in the password and log in
4. Connect through Serial Port
Connect the G88 with a serial cable to the control PC (cable included in
the package)
If the software was connected via UART (RS232) last time, software will connect to the G88 automatically vis RS232. If
it was used at Network last time, a ‘Network Timeout’ error message will be shown on screen and users need to set up
as below for RS232 connection in the software
• Choose ‘UART’ instead of ‘Network’
• Select the COM port from the Port dropdown menu
• Press ‘Disconnected’ button to connect
5. Connect through Network
The default IP address for G88 controller is 192.168.0.247, Users need to change the IP address of the control PC to
static IP address and the same network segment as the G88 at TCP/IPv4 in Ethernet Properties
IP address: any address between 192.168.0.2 and 192.168.0.254 except the address which has been taken by the
G88
Subnet mask: 255.255.255.0, Default Gateway: 192.168.0.1
Produktspecifikationer
| Varumärke: | SEADA |
| Kategori: | Processor |
| Modell: | G88-HDMI |
Behöver du hjälp?
Om du behöver hjälp med SEADA G88-HDMI ställ en fråga nedan och andra användare kommer att svara dig
Processor SEADA Manualer
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
Processor Manualer
- SPL
- Toa
- Allen-Heath
- FabFilter
- Vivolink
- Warm Audio
- GeoBox
- Audison
- Noise Engineering
- LD Systems
- Henry Engineering
- Decimator
- Allen & Heath
- KanexPro
- MuxLab
Nyaste Processor Manualer
10 Oktober 2025
5 Oktober 2025
5 Oktober 2025
5 Oktober 2025
5 Oktober 2025
5 Oktober 2025
5 Oktober 2025
5 Oktober 2025
5 Oktober 2025
5 Oktober 2025