Siemens WM16S890EU Bruksanvisning

Siemens tvättmaskin WM16S890EU

Läs gratis den bruksanvisning för Siemens WM16S890EU (10 sidor) i kategorin tvättmaskin. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 10.5 recensioner. Har du en fråga om Siemens WM16S890EU eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/10
1
Safety instructions
The washing machine is heavy  take care when lifting it.
Warning: Frozen hoses may tear/burst. Do not install the washing machine in an area where
there is a risk of frost or outdoors.
Do not hold onto protruding parts (e.g. loading door) when lifting. Washing machine may
be damaged.
Before transporting the appliance, always drain dispensers. aPage 8
In addition to the safety information listed here, the local water and electricity supplier may
have special requirements.
If in doubt, have the appliance connected by a technician.
Lay hoses and cables in such a way that there is no risk of stumbling.
Environmental disposal
Dispose of packaging in an environmentally friendly manner.
This appliance has been identified in accordance with the European Directive 2002/96/EG
on Waste Electrical and Electronic Equipment (WEEE).
The Directive specifies the framework for an EU-wide valid return and recycling of waste
appliances.
Installation area
Stability is important to prevent the machine from moving!
The installation area must be firm and level.
Soft floors/floor coverings are not suitable.
If installing the appliance on a base
secure the washing machine feet with retention plates *.Always
* Order no. WMZ 2200, WX 9756, CZ 110600, Z 7080X0
If installing the appliance on a wooden joist ceiling
If possible, install the washing machine in a corner.
Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
secure the washing machine feet with retention plates.Always
* Order no. see above
Installation on a platform with drawer*
* Order no. WMZ20490, WZ20490
Built-under/Built-in appliance
Build-under/Build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
60 cm cavity width required.
Install washing machine only under a continuous worktop connected firmly to the adjacent
cupboards.
Built-under
Risk of electric shock!
Instead of the appliance cover panel, it is to have a technician fit a sheet metal essential
cover *. * Order no. WMZ 2043, WZ 20430
60 cm cavity width required.
2
Scope of delivery depending on model
not included in product package:
When drainage is into a siphon, a Ø 2440 mm hose clip (specialist outlet) is also required.
a Water connection, Page 4
Useful tools:
Spirit level for aligning the washing machine.
Size 13 socket wrench:
for loosening the transportation protection devices and aPage 3
size 17: for aligning the appliance feet. aPage 5
Hose and cable lengths depending on model
Connection on left side or Connection on right side
Note: If the hose holders are used, the possible hose lengths are reduced!
Available from dealer/customer service:
Extension for Aqua-Stop or cold water inlet hose (approx. 2.50 m).
Order no. WMZ2380, WZ10130, CZ11350, Z7070X0
Longer supply hose (approx. 2.20 m), for standard model.
Spanner
(depending on model)
Power cord
Water supply
Water drainage
Elbow
for securing the
drainage hoseCovers
Aqua Stop Aqua-Secure
~140 cm
~95 cm
~120 cm
~130 cm
~100 cm
~135 cm
0  max. 100 cm
Humidity in the drum
is caused by the final
inspection.
3
Remove transportation protection devices
Before using the appliance for the first time, remove the
4 transportation protection devices completely and keep in a safe
place.
If the appliance is to be transported at a later date, re-install the
transportation protection devices  prevents damage to the machine.
aPage 6
Keep screw and sleeve together.
1. Take hoses (depending on model) out of the
holders and the elbow. Remove the elbow.
2. Loosen and remove all 4 transportation lock screws.
3. Take the power cord out of the holders.
Remove sleeves.
4. Insert covers and lock firmly by pressing on the locking hook at the top.
4
Water connection depending on model
Do not immerse Aqua-Stop safety device in water (contains Risk of electric shock!
an electric valve).
To prevent leakage or water damage, follow the instructions in this chapter!
The washing machine must only be operated with cold tap water.Caution:
Do not connect to the mixer tap of an unpressurised hot-water apparatus.
Use only the supplied inlet hose or one purchased from an authorised specialist outlet,
not a used one!
If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
Caution: do not kink, crush, modify or sever
(strength is no longer guaranteed).
Optimum water pressure in the mains: 1001000 kPa (110 bar)
When the tap is turned on, the water flow is at least 8l/min.
If the water pressure is higher, install a pressure reducing valve.
Model: Aqua-Stop
Aqua-Secure
Standard
1. Connect water inlet hose to a 3/4" = 26.4 mm tap.
Caution: Tighten plastic screw-fittings by hand only.
2. Carefully turn on the tap and check that the connection
points are not leaking.
Caution: Screw connection is under water pipe
pressure.
Water drainage
Water drainage hose:
Caution: Do not bend or pull.
Height difference between installation area and outlet:
0  max. 100 cm
Drainage into a washbasin:
Caution: Secure the drainage hose to prevent it from slipping out of the
sink.
Caution: The plug must not block the drain of the wash basin. When the
water is being pumped out of the washing machine, check that the water
drains away quickly enough. The end of the drainage hose must not be
immersed in the drained water! Risk of water being drawn back into the
washing machine!
Drainage into a siphon:
Caution: Connection point must be secured with hose clip, Ø 2440 mm
(specialist outlet).
. Drainage into a plastic pipe with rubber sleeve or into a gully:
Caution: Secure the drainage hose to prevent it from slipping out of the
sink.
max.
90°
max.
90°
min.
10 mm
min.
10 mm
3/4
3/4
5
Alignment
Loud noise formation, intense vibrations and wandering may be due to incorrect
alignment!
Align washing machine with spirit level
1. Loosen lock nut in a clockwise direction with a wrench.
2. Change height by rotating the appliance feet.
Caution: All four feet must be firmly on the floor.
The washing machine must not wobble!
Check alignment of the washing machine with a spirit level and, if
required, correct.
3. Tighten the lock nut against the housing.
Grip the foot and do not adjust the height.
Caution: The lock nuts on all four appliance feet must be screwed tightly
against the housing!
Electrical connection
ʑConnect the washing machine to an alternating current via a correctly installed
earthed socket only.
ʑThe mains voltage and voltage specifications on the washing machine (appliance
rating plate on the rear of the appliance) must match.
ʑConnected load as well as required fuse are indicated on the appliance rating plate.
ʑEnsure that:
the mains plug and socket match,
the cable cross-section is adequate,
the earthing system has been installed correctly.
ʑA damaged power cord may be replaced by an electrician only.
A replacement mains cable can be obtained from customer service.
ʑDo not use multiple plugs/couplings or extension cables.
ʑIn the event that an earth leakage circuit breaker is to be used, only use types
marked with the following symbol: .
Only this symbol can guarantee compliance with all current regulations.
ʑMains plug:
Do not insert/pull out with damp hands.
Do not pull by tugging the power cord.
Never pull it out during operation.
max. 12 mm


Produktspecifikationer

Varumärke: Siemens
Kategori: tvättmaskin
Modell: WM16S890EU

Behöver du hjälp?

Om du behöver hjälp med Siemens WM16S890EU ställ en fråga nedan och andra användare kommer att svara dig