Snap Circuits Basic Electricity SCP-10 Bruksanvisning
Snap Circuits
Leksaker
Basic Electricity SCP-10
Läs gratis den bruksanvisning för Snap Circuits Basic Electricity SCP-10 (5 sidor) i kategorin Leksaker. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 10.5 recensioner. Har du en fråga om Snap Circuits Basic Electricity SCP-10 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/5
If you have any problems, contact Elenco
®
Copyright © 2014 Elenco®Electronics, Inc. All Rights Reserved. 150 Carpenter Ave. Wheeling, IL 60090● ●
(800) 533-2441 Fax: (847) 520-0085 e-mail: elenco@elenco.com Website: www.elenco.com or www.snapcircuits.net● ●
WARNING: SHOCK HAZARD -
Never connect Snap Circuits®
to the electrical outlets in your
home in any way!
WARNING: Always check your wiring before
turning on a circuit. Never leave a circuit
unattended while the batteries are installed.
Never connect additional batteries or any other
power sources to your circuits.
Basic Electricity
Model SCP-10
753159
Snap Circuits®uses electronic
blocks that snap onto a base
grid to build different circuits.
These blocks have different
colors and numbers on them so
that you can easily identify
them. Build the circuit shown by
placing all the parts with a black
1next to them on the clear base
grid first. Then, assemble parts
marked with a . Install three (3)2
“AA” batteries (not included)
into the battery holder (B3).
Set the meter (M5) to the 1A
setting.
Turn on the slide switch (S1).
The lamp (L4) comes on, and
the meter measures how much
electric current is flowing.
Project 1 Project 2 Lamp Current Batteries in Series
Electricity is the movement of sub-atomic charged
particles through a material due to electrical pressure
across the material, such as from a battery. Power
sources, like batteries, push electricity through a circuit,
like a pump pushes water through pipes. Wires carry
electricity, like pipes carry water. Devices like lamps use
the energy in electricity to do things. Switches control the
flow of electricity like valves and faucets control water.
The electrical pressure exerted by a battery or other
power source is called and is measured in voltage volts
(V). The “+” and “–” signs on a battery indicate which
direction it will “pump” electricity.
The is a measure of how fast electricityelectric current
is flowing in a wire, just as the water current describes
how fast water is flowing in a pipe. It is expressed in
amperes milliamps(A) or (mA = 1/1,000 of an ampere).
The “ ” of electricity is a measure of how fast energypower
is moving through a wire. It is a combination of the voltage
and current (Power = Voltage x Current). It is expressed in
watts (W).
The of a component or circuit represents howresistance
much it resists the electrical pressure (voltage) and limits the
flow of electric current. The relationship is Voltage = Current
x Resistance. When resistance increases, less current flows.
Resistance is measured in ( ).ohms W
If desired, use the voltage measured here (with 3 batteries) and the
current measured in project 1 to calculate the resistance and power of
the lamp:
Resistance equals Voltage divided by Current, and should be about 15
ohms. Power equals Voltage times Current, and should be about 1 Watt.
Your results may be different, because M5 is a simple meter with low
accuracy, and your battery voltage can vary.
1A
5V
Set the meter (M5) to the 5V setting, and turn on the slide
switch (S1). The lamp (L4) comes on, and the meter measures
the voltage from the 3 batteries.
Part B: Remove the left battery from the holder (B3), then snap
one side of the red jumper jumper on as shown, and touch
metal on the other end to the left spring in the battery holder.
Read the voltage on the meter, measuring 2 batteries, and
notice how the lamp is dimmer.
Part C: Now also remove the center battery from the holder and
touch metal on the end of the red jumper wire to the center
spring in the holder. Read the voltage on the meter, measuring
1 battery, and notice how the lamp is dimmer.
Placement
Level Numbers
Quiz answers:
1. B 2. B 3. C 4. A 5. B
Batteries are like electrical pressure, pushing electricity
through a circuit. Adding more batteries increases the
flow of electricity, making the lamp brighter.
Part B:
Part C:
Produktspecifikationer
| Varumärke: | Snap Circuits |
| Kategori: | Leksaker |
| Modell: | Basic Electricity SCP-10 |
Behöver du hjälp?
Om du behöver hjälp med Snap Circuits Basic Electricity SCP-10 ställ en fråga nedan och andra användare kommer att svara dig
Leksaker Snap Circuits Manualer
30 Augusti 2024
29 Augusti 2024
28 Augusti 2024
25 Augusti 2024
25 Augusti 2024
Leksaker Manualer
- Thames & Kosmos
- Lenoxx
- Schleich
- Valk
- Dualsky
- Joy-it
- Geomag
- Bright Starts
- Quadro
- Swurfer
- Valley Dynamo
- Viessmann
- Lionelo
- Kinderkraft
- Unico Plus
Nyaste Leksaker Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
8 April 2025