Stanley Bostitch P50 Bruksanvisning

Stanley hammare Bostitch P50

Läs gratis den bruksanvisning för Stanley Bostitch P50 (1 sidor) i kategorin hammare. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 1.5 recensioner. Har du en fråga om Stanley Bostitch P50 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/1

ASSEMBLY:

1. Apply “O” ring lube to all “O” rings.

2. Apply a light coat of “O” ring lube to cylinder walls in valve barrel.

3. Assemble “O” ring to piston.

4. Insert piston in valve barrel.

5. Insert internal “O” ring in end of valve barrel.

CAUTION: do not assemble “O” ring of valve plug as it may be

damaged during assembly in valve barrel by sharp edges of retaining

ring groove.

6. Insert valve plug in valve barrel.

7. Push valve plug to squeeze internal “O” ring, and assemble

retaining ring.

8. Screw hose ﬁtting into valve barrel and tighten.

9. Assemble external “O” rings on valve barrel.

INSTALLATION:

NOTE: Refer to Model P50 Series Air Drive Plier

1. Disconnect air supply.

2. Remove trigger.

3. Drive out valve barrel roll pin, and remove valve barrel and stem.

CAUTION: Do not mar outside diameter of valve stem. Valve unit can

be removed by applying 20 PSI from air supply.

4. The valve stem and roll pin are required for use with remote control

parts. All other parts removed are not required when spare parts

are installed.

NOTE: If plier is to be ﬁxtured and clincher blade will not be required,

it should be removed at this point.

5. Remove magazine.

6. Insert valve stem in remote control valve barrel.

7. Insert remote control valve barrel in frame with hose ﬁtting facing

rear.

8. Reassemble roll pin locking valve barrel in place.

9. Reassemble magazine.

10. Attach 1/4 O.D. plastic tubing to remote control valve ﬁtting and

connect other end to half union assembled on the outlet (“CYL”)

port of the three way normally closed foot valve.

NOTE: A 1/4” three way normally closed valve will operate several

pliers. Increase size of valve will operate several pliers. Increase size of

valve to suit number of pliers to be controlled.

11. Attach 1/4” MPT tee to the back of the frame (main air supply).

Attached half union to the tee and attach 1/4 O.D. plastic tubing

between half union in the tee to the half union on the inlet (“IN”)

port of the three way normally closed foot valve.

12. If plier is to be mounted in ﬁxture, assemble at this point.

13. If clincher blade has been removed, assemble clincher provided

in kit to ﬁxture. The 5/16-18 UNC thread shaft should ﬁt snug in

a straight clearance hole. Secure with lock washer and hex nut

provided.

INSTALLATION OF ADDITIONAL TOOL TO THIS UNIT:

1. The air supply to the plier or additional pliers must have sufﬁcient

air ﬂow to operate all pliers. Each plier in a multiple mount must

have an individual pig tail in an air supply or reservoir to prevent

the starving of the pliers for air driving operation.

2. To install additional pliers to the original unit will require a P50181

Remote Control Kit for each plier.

3. Also to install additional pliers will require a 1/4” PL x 1/4” PL x

1/4” PL tee to insert in plastic tubing between the remote control

valve and the outlet (“CYL”) port of the three way normally closed

foot valve.

4. Additional plastic tubing 85334-10 (1/4” O.D.) may be required to

connect pliers and can be ordered from Bostitch.

OPERATION:

1. Connect air supply to plier.

2. Air pressure must be identical for plier and remote control valve.

3. Actuation of remote control valve will operate plier and drive

staple.

4. Release of remote control valve will return driver piston.

CAUTION: Do not attempt to operate plier without material over

clincher to avoid damage to driver tip.

P50 AND P51 AIR DRIVER PLIER

INSTRUCTIONS FOR ASSEMBLY, INSTALLATION AND

OPERATION OF REMOTE CONTROL KIT WITH FOOT

VALVE AND CLINCHER

9R196709RA 09/12

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI speciﬁcations and provides protection against ﬂying particles both from the FRONT and SIDE should ALWAYS be worn by the

operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against ﬂying fasteners and

debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards

Institute, ANSI Z87.1, CAN/CSA Z94.4 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate

protection.

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different

work area, as accidental actuation may occur, possibly causing injury.

Do not use gasoline or similar highly ﬂammable liquids to clean the nailer. Vapor in the nailer could be ignited by a spark causing the tool to explode.

When working on air tools, note the warnings and cautions in this guide and in the Operation and Maintenance Manual covering the speciﬁc tool. USE EXTRA CARE WHEN

EVALUATING PROBLEM TOOLS.

OPERATION AND MAINTENANCE MANUALS ARE AVAILABLE FREE OF CHARGE FROM BOSTITCH

1-800-556-6696 OR WWW.BOSTITCH.COM