Sunding SD-579 Bruksanvisning
                    Sunding
                    
                    Inte kategoriserad
                    
                    SD-579
                
                                
    Läs gratis den bruksanvisning för Sunding SD-579 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 8 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 4.5 recensioner. Har du en fråga om Sunding SD-579 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
                        Sida 1/2
                    
                    
                    
-TRIP UP  TRIP  DISTANCE    COUNT UP
-TRIP DN  TRIP  DISTANCE  COUNT DOWN 
-CAL  CALORIE
-FAT   FATBURN
-COMPARATOR
-Km/Mile SELECTION
-SLEEP  MODE 
- MAINTENANCE  ALERT  
- SETTING  TYRE  CIRCUMFERENCE 
-SETTING LAST VALUE OF ODOMETER/ODO
-SETTING  TTM
-COMPUTER LOW  BATTERY  INDICATOR 
-SENSOR LOW  BATTERY  INDICATOR
- AUTO  BACK  LIGHT
-WIRELESS  AUTO WAKE UP
- AUTO  ON/OFF
SD 579C-                                       V1 .0
FUNCTIONS ILLUSTRATIONS
WHAT IS IN THE PACKAGE
COMPONENT ILLUSTRATIONS
-SPD   CURRENT SPEED 
-ODO   ODOMETER
-DST   TRIP  DISTANCE  
-MXS   MAXIMUM  SPEED 
-AVS   AVERAGE  SPEED 
-TTM   TOTAL  TRIP  TIME 
-TM    TRIP  TIME 
-RAT   RIDING  ALL  TIME (SINGLE TRIP TIME)   
-CLK   CLOCK   12H/24H 
-SW    STOPWATCH 
-Th   TEMPERATURE
-MAX Th   MAXIMUM TEMPERATURE
-MIN Th   MINIMUM TEMPERATURE
-TM UP    TRIP  TIME COUNT UP  
-TM DN    TRIP  TIME  COUNT DOWN
1
2
3
5
6
4
3mm
Computer unit and mount installation
2
To attach the speedometer sensor, use the ties to secure it to the front
fork. Make sure the computer and the sensor are on the same side of
the fork and no more than 60cm apart. The sensor should have an
arrow pointing at the magnet. Follow the figure to install the magnet on
a spoke. The gap between the sensor and the magnet should be 3 mm.
Notice
The magnet is designed for spokes 
that are less than 2mm thick
Pass bicycle spokes through the 
plastic hole on the bottom of the 
magnet and tighten to secure
Computer
CR2032 Battery
Magnet
Mounting Shoe
Sensor
Ties
1
2
3
4
5
6
Please note that the slight noise when the computer unit shakes is the built-in ball switch, which is a 
normal phenomenon caused by the wireless automatic wake-up function design.
Installation diagram of
magnet and Sensor
INSTRUCTION
Avoid exposing the device to direct sunlight or high temperature for too
long. Let it cool down in the shade for a while.
3.Black display
4.Display shows incomplete figures.
5.Display readout fades out
1.The speedometer shows 0 km/h while riding.
Improper magnet/sensor alignment, or the distance between
the computer and the sensor is more than 80cm.
2.The speedometer shows wrong values.
 Take out the battery and reset it after 10 seconds.
Poor battery contact or dead battery .Check the installation of the battery or change a new battery.
The battery voltage is low, change a new battery.
MALFUNCTIONS AND REASONS
MODE INSTRUCTION
After inserting the battery, the screen enters the total distance/time mode. Press the MODE button to cycle through single 
distance/time mode, count up/down mode and fat/calorie mode in turn. In the total distance/time mode, count up/down 
mode and fat/calorie mode, it will automatically return to the single distance/time modeafter 8 seconds of no operation.
ODO / TTM MODE DST / TM MODE CAL / FAT MODECOUNTUP / DOWN MODE 
1
FRONT BACK
COMPUTER & 
MOUNTING
SHOE TRIGGER
BATTERY
COVER
MAINTENANCE ALERT 
COMPARATOR
LOW BATTERY INDICATOR   
Computer unit interface
MODESET
SPEED
TIME
Computer battery
 installation: Open the 
battery cover.  Install  
CR2032 batteries with 
positive poles facing 
battery cover.  
Match base alignment with 
computer and insert to attach.
Thread ties through the slots under 
the base to attach to handlebar.
Produktspecifikationer
| Varumärke: | Sunding | 
| Kategori: | Inte kategoriserad | 
| Modell: | SD-579 | 
Behöver du hjälp?
Om du behöver hjälp med Sunding SD-579 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Sunding Manualer
                        
                         31 Januari 2025
                        
                    
                                                            
                        
                         31 Januari 2025
                        
                    
                                                            
                        
                         31 Januari 2025
                        
                    
                                                            
                        
                         31 Januari 2025
                        
                    
                                                            
                        
                         29 Januari 2025
                        
                    
                                                            
                        
                         29 Januari 2025
                        
                    
                                                            
                        
                         29 Januari 2025
                        
                    
                                                            
                        
                         29 December 2024
                        
                    
                                                            
                        
                         9 September 2024
                        
                    
                                                            
                        
                         8 September 2024
                        
                    
                                                            Inte kategoriserad Manualer
- 2box
- Shimbol
- Maxi-Cosi
- Dresden Elektronik
- Ricoh
- Zaor
- Zalman
- Peak Design
- CSL
- Boneco
- Argus
- CkeyiN
- Hansa
- TP Link
- Bolt
Nyaste Inte kategoriserad Manualer
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025
                        
                    
                                                            
                        
                         9 April 2025