Sunding SD-581C Bruksanvisning
Sunding
Inte kategoriserad
SD-581C
Läs gratis den bruksanvisning för Sunding SD-581C (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 8.5 recensioner. Har du en fråga om Sunding SD-581C eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
CLK Mode(12H/24H)
Computer Battery Installation
While the default Maintenance Alert digit
200 RIGHTkm/m is flashing, Press the button
to choose km/m. Press the 200/400/600/800 LEFT
button to confirm and enter into mode. BASIC ALL Or select
(when the the Maintenance Alert digit you set, the ODO
will appear on the screen to alert the rider, press the RIGHT
button seconds to cancel it.)3
24 Function
Instruction Manual V0.1
Remove the battery cover from the bottom of the computer by using a
flat blade screwdriver, install battery with the positive (+) pole facing the
battery cover and replace the cover. Should the LCD show irregular
figures, take out the battery and reinstall it.
Attach the mounting shoe with the cable ties
to the handlebars as shown in the diagram.
Attach the computer to the mounting shoe
by sliding the unit until it snaps firmly into
position. To remove, press down on the
release catch, and remove the computer. To
check for proper speed function and sensor
alignment, spin the front wheel with the
computer in speed mode. Adjust the position
of sensor and magnet if there is on or weak
signal.
Computer
Long press + button for 3 seconds to enter setting modeLEFT RIGHT .
‘ ’ appears on the screed when the battery has been installed, with 2060
one figure flashing enter the wheel circumference using the formula
below.
In the example above you would enter . Press the button to 2198 RIGHT
advance the digits as needed and the button to confirm and LEFT
advance. (The circumference ranges 0mm~9999mm), press the LEFT
button to enter mode.KM/M
Setting(km/h)/(m/h)
Press the button to choose or .RIGHT km/h m/h
Press the button to enter mode.LEFT CLOCK
Setting Maintenance alert
In CLOCK Mode, press the button for seconds LEFT 3
to enter 12/24H selection. Press once more to swap
between 12/24 hours. Press the RIGHT button to enter
the Hour mode, when the figure indicating HOUR starts
to flash, press the LEFT button to adjust it. Continue to
press the RIGHT button to enter the Minute mode, when the figure
indicating MINUTE starts to flash, press the LEFT button to adjust. Press
the RIGHT button to confirm & press the RIGHT button again to switch to
ODO mode.
SD-581C Bicycle Computer
Installation of Speedometer
Attach speedometer sensor to the front fork using the ties. The
computer and sensor should be installed on the same side of the
fork, with distance between them of less than 60cm. The arrow
on the sensor should point at the magnet. Install magnet as
shown in figure. Distance between sensor and magnet should
be 3.0mm.
NOOFF
-SPD Current Speed
- ODO Odometer (0~99999km/m)
- DST Trip Distance
- MXS Maximum Speed
-AVS Average Speed
- TM Elapsed Time
- CLK Clock (12H/24H)
- TMP Temperature / (-10°C~70°C)
- MIN TMP Minimum Temperature
- MAX TMP Maximum Temperature
-CAL Calories Expended
- FAT Fat Burned
-SCAN
- “+”“-”Comparator
- SETTING SPEED SCALE (km/h,m/h)
- SETTING TYRE CIRCUMFERENCE / (0mm~9999mm)
- SETTING THE LAST VALUE OF ODOMETER / ODO
- MAINTENANCE ALERT
-FREEZE FRAME MEMORY
-LOW BATTERY INDICATOR
-BASIC OR ALL
-SMART BACKLIGHT
-BACKLIGHT IS LONG BRIGHT
- AUTO ON/OFF
Setting Rider’s Weight
The default weight is 65kg, press the button to adjust the RIGHT
flashing weight number according to rider’s weight, press buttonLEFT
to confirm and advance. Weight ranges : 20~150kg. Press the LEFT
button to enter into Maintenance Alert setting.
Computer
Sensor
Magnet
Notice
Pass bicycle spokes through the
plastic hole on the bottom of the
magnet and tighten to secure
The magnet is designed for
spokes that are less than
2mm thick.
FUNCTIONS
Mounting Shoe
Installation
Parameter Settings
Wheel Size Input
3.0mm
BASIC Or ALL
Press the RIGHT button select BASIC OR ALL, Press the LEFT
button to confirm and enter into Clock mode. “BASIC” Indicates that the
menu displays basic functions except for MIN TMP \ MAX TMP\ and CAL
FAT.
“ALL” Indicates that the menu displays all functions including MIN TMP \
MAX TMP \ CAL FAT and .
Produktspecifikationer
| Varumärke: | Sunding |
| Kategori: | Inte kategoriserad |
| Modell: | SD-581C |
Behöver du hjälp?
Om du behöver hjälp med Sunding SD-581C ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Sunding Manualer
31 Januari 2025
31 Januari 2025
31 Januari 2025
31 Januari 2025
29 Januari 2025
29 Januari 2025
29 Januari 2025
29 December 2024
9 September 2024
8 September 2024
Inte kategoriserad Manualer
- N8WERK
- SoundMagic
- Enerdrive
- Scotsman
- Inverto
- Palm
- Nec
- SilverStone
- DataComm
- V-Tac
- Maxdata
- Bush
- IBEAM
- AVMATRIX
- Dayclocks
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025