Trotec BD6A Bruksanvisning
Trotec
Inte kategoriserad
BD6A
Läs gratis den bruksanvisning för Trotec BD6A (10 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 13 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 7 recensioner. Har du en fråga om Trotec BD6A eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/10
TRT-BA-BD6A-TC230123TTRT05-001-EN
BD6A
EN
ORIGINAL INSTRUCTIONS
CROSS LINE LASER
2 EN
cross line laser BD6A
Table of contents
Notes regarding the instructions .........................................2
Safety .....................................................................................2
Information about the device................................................4
Available accessories ...........................................................5
Transport and storage...........................................................5
Operation ...............................................................................5
Maintenance and repair ........................................................8
Errors and faults....................................................................8
Disposal .................................................................................9
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of laser radiation
This symbol indicates dangers to the health of persons
due to laser radiation.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
BD6A
https://hub.trotec.com/?id=47206
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use.
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
• Do not use the device in potentially explosive rooms or
areas and do not install it there.
• Do not use the device in aggressive atmosphere.
• Do not immerse the device in water. Do not allow liquids to
penetrate into the device.
• The device may only be used in dry surroundings and must
not be used in the rain or at a relative humidity exceeding
the operating conditions.
• Protect the device from permanent direct sunlight.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Do not open the device.
• Avoid looking directly into the laser beam.
• Never point the laser beam at people or animals.
• Never charge batteries that cannot be recharged.
• Different types of batteries and new and used batteries
must not be used together.
• Insert the batteries into the battery compartment according
to the correct polarity.
• Remove discharged batteries from the device. Batteries
contain materials hazardous to the environment. Dispose
of the batteries according to the national regulations.
• Remove the batteries from the device if you will not be
using the device for a longer period of time.
• Never short-circuit the supply terminal in the battery
compartment!
• Do not swallow batteries! If a battery is swallowed, it can
cause severe internal burns within2hours! These burns
can lead to death!
EN 3
cross line laser BD6A
• If you think batteries might have been swallowed or
otherwise entered the body, seek medical attention
immediately!
• Keep new and used batteries and an open battery
compartment away from children.
• Only use the device, if sufficient safety precautions were
taken at the surveyed location (e.g. when performing
measurements along public roads, on building sites etc.).
Otherwise do not use the device.
• Observe the storage and operating conditions (see
Technical data).
Intended use
Only use the device for the projection on non-reflectiveBD6A
surfaces as an aid to determine and check horizontal, vertical
and/ or parallel lines. Observe and comply with the technical
data.
To use the device for its intended use, only use accessories and
spare parts which have been approved by Trotec.
Any use other than the intended use is regarded as misuse.
Foreseeable misuse
Do not use the device in potentially explosiveBD6A
atmospheres or in liquids. Never point it at people or animals.
Trotec accepts no liability for damages resulting from improper
use. In such a case, any warranty claims will be voided.
Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
laser measuring devices.
• have read and understood the instructions, especially the
Safety chapter.
Safety signs and labels on the device
Note
Do not remove any safety signs, stickers or labels from
the device. Keep all safety signs, stickers and labels in
legible condition.
The following safety signs and labels are attached to the device:
Safety symbol Meaning
The warning sign is located on the side of
the device and indicates that the device is
equipped with a class2 laser.
The power is less than 1mW. The
frequency range of the laser is630 to
670nm.
Do not look directly into the laser beam
or the opening from which the laser
beam emerges!
The warning sign is located above the laser.
Do not look directly into the laser beam
or the opening from which the laser
beam emerges!
The warning sign is located on the side of
the device and indicates that the gimbal
suspension of the laser must be disabled
before transport.
To do so, the switch must be set to
the position.
Produktspecifikationer
| Varumärke: | Trotec |
| Kategori: | Inte kategoriserad |
| Modell: | BD6A |
Behöver du hjälp?
Om du behöver hjälp med Trotec BD6A ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Trotec Manualer
8 Oktober 2024
4 Oktober 2024
29 September 2024
27 September 2024
24 September 2024
23 September 2024
23 September 2024
22 September 2024
16 September 2024
16 September 2024
Inte kategoriserad Manualer
- Real Cable
- RF-Links
- Furman
- Eldat
- Chacon
- Termozeta
- Mitsai
- Lockwood
- Einhell
- Samsung
- Suntec
- Nevir
- Urban Glide
- Barco
- EXO
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025