Valcom VIP-9880A Bruksanvisning

Valcom högtalare VIP-9880A

Läs gratis den bruksanvisning för Valcom VIP-9880A (3 sidor) i kategorin högtalare. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 2 recensioner. Har du en fråga om Valcom VIP-9880A eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/3

1 947636

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

ISSUE 1

VIP-9880A

IP FlexHorn with Square Grille

INTRODUCTION

The VIP-9880A IP FlexHorn with grille enables

loudspeaker voice paging anywhere on an

Ethernet network. The VIP-9880A consists of a

high efficiency Class-D Horn and a Network

Interface, allowing stand alone capability when

used with a SIP-enabled telephone system or can

be accessed from a variety of Valcom managed

VoIP products. Power is provided to the

VIP-9880A via a Power over Ethernet (PoE)

switch meeting the 802.3af specication.

SPECIFICATIONS

Access Methods

 SIP-enabled telephone system

 PBX, FXO Port w/VIP-811

 POTS telephone set w/VIP-811

 PBX, FXS Port w/VIP-821

 Valcom M Cast Page Group

Features

 RJ-45 for network connection

 Network activity LEDs

 Power over Ethernet 802.3af compatible

 White painted steel faceplate

Dimensions/Weight

 10.75” H x 10.75" W x 4.0" D

(27.3cm H x 27.3cm W x 10.2cm D)

 Weight: 3.1 lbs. (1.4 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: -10dBm nominal

Nominal Power Requirements

Via 802.3af (PoE) Ethernet Switch: Class 3

Environment

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Packing List

Precautionary Designations

Qty Item

1 VIP-9880A IP FlexHorn w/Grille

1 VSP Document

2 947636

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

INSTALLATION

Operation

The VIP-9880A provides IP loudspeaker paging

access via network connection to customer

telephone system or stand alone telephone set.

Interface to customer telephone system can be

via SIP registration, FXO or FXS port (with

appropriate PBX connection and Valcom

VIP-81x/82x).

Mounting

The VIP-9880A is designed for flush mounting on

a hollow surface or to a Valcom backbox. Using

Figure 1 as a guide, cut a hole in the mounting

surface large enough to allow recessing the

FlexHorn into the wall. Please note the depth

requirement necessary for ush mounting as

shown in Figure 1. Next, drill mounting holes in

the surface to align with the four mounting holes

in the grille. Using appropriate anchors and

screws (not included), mount the VIP-9880A to

the surface. Alternatively, Valcom’s backbox

model VB-R17-D is available for mounting this

model.

Power Connections

The only method of powering a VIP-9880A

Network Interface is via a Power over Ethernet

(PoE) network switch or power injector meeting

the 802.3af specification.

Network Connection

The VIP-9880A has one RJ-45 Ethernet network

connector on the circuit board. Use a standard

Ethernet patch cable to connect the Ethernet

connector of the VIP-9880A to an Ethernet

switch.

Signal Connections

Audio signal connections from the network

interface to the FlexHorn are provided through a

screw terminal and are pre-wired at the factory.

No further connections are required.

Status Indicator Lights

The VIP-9880A Network Interface has 2 status

indicator lights on the RJ-45 Ethernet connector.

Green LED: (Link) Indicates Ethernet connection

when illuminated.

Yellow LED: (Activity) Indicator flashes to

indicate network activity.

Setup

Information specific to your application will need

to be programmed into the VIP-9880A using a

computer. The PC used for programming should

be connected to the same subnet as the

VIP-9880A. Setup will be done using the IP

Solutions Setup Tool. The IP Solutions Setup

Tool may be downloaded from the Valcom web

site at http://www.valcom.com/vipsetuptool.

TECHNICAL ASSISTANCE

Assistance in troubleshooting is available from

the factory. Call (540) 563-2000 and press 1 for

Technical Support or via email at

support@valcom.com.

When requesting assistance, you should include

all available information. It is strongly suggested

that you go to the web site and follow the trouble

resolution procedure at http://www.valcom.com.

Valcom equipment is not field repairable.

Valcom, Inc. maintains service facilities in

Roanoke, VA. Should repairs be necessary,

attach a tag to the unit clearly stating your

company name, address, phone number, contact

person and the nature of the problem. Send the

unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

3 947636

FIGURE 1. MOUNTING

VALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of

normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or refund

of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts

and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to

additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any

anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,

maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the

specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without

limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified

immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: (540) 563-2000 FAX: (540) 362-9800