Vent-A-Hood SLH9230SS Bruksanvisning

Vent-A-Hood Fläktkåpa SLH9230SS

Läs gratis den bruksanvisning för Vent-A-Hood SLH9230SS (2 sidor) i kategorin Fläktkåpa. Guiden har ansetts hjälpsam av 23 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 12 recensioner. Har du en fråga om Vent-A-Hood SLH9230SS eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Page 1L109 0516A

CUS

Read and Save These Instructions

All Hoods Must Be Installed By A Qualied Installer

INSTALLATION INSTRUCTIONS

UNDER CABINET HOOD

Read All Instructions Thoroughly Before Beginning Installation

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualied person(s)

in accordance with all applicable codes and standards, including re-

rated construction. Switch power o󰀨 at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally

during installation.

B. When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

C. Ducted fans must always be vented to the outdoors.

D. Su󰀩cient air is needed for proper combustion and exhausting of gases

through the ue (chimney) of fuel burning equipment to prevent back

drafting. Follow the heating equipment manufacturer’s guideline and

safety standards such as those published by the National Fire Protection

Association (NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and local code authorities.

E. ASHRAE residential ventilation standard 62.2 limits exhaust fans (total) to

a maximum of 15 CFM per 100 square feet of occupiable space, unless a

back drafting test is performed or make-up air is provided. Consult a local

HVAC engineer for make-up air evaluation.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL

DUCTWORK

Page 2L109 0516A

Ducting Do’s and Don’ts

YES

Smooth Duct

Smooth Gradual Turn

Proper Combining

of Two Ducts

Flexible Duct

Sharp Angled Turns

Improper Combining

of Two Ducts

General Requirements

• Observe local codes regarding special duct requirements and placement of duct against combustibles.

• UsingVent-A-Hoodtransitions(backpage)willensurepropere󰀩ciency.

• UsingVent-A-Hoodroofjacksorwalllouvers(backpage)willensurepropere󰀩ciency.

• Where possible, seal joints with duct tape.

• The hood must be ducted to the outdoors without restrictions.

Blower Requirements

• The single blower unit (B100) requires 6” round duct or equivalent (28 square inches), and the dual

blower unit (B200) requires 8” round duct or equivalent (50 square inches).

Blower Combined Duct Dize Sq. Inch Area Vent-A-Hood Transition

Single (B100) 6" round or equivalent 28 sq. in. N/A

Dual (B200) 8" round or equivalent 50 sq. in. N/A

Single and Dual (B100 & B200) 10" round or equivalent 79 sq. in. VP562 (Optional)

Two Duals (Two B200s) 12" round or equivalent 113 sq. in. VP563 (Optional)

Ducting Requirements

• NEVER reduce the duct size.

• Whencombiningductstogether,thesquareinchareamustreectthetotalsquareinchareaofthe

ducts being combined.

• Donotuseexibleorcorrugatedduct.Thistypeofductwillrestrictairowandreduceperformance.

• Onlyusesmooth,galvanized,metalduct.

• Make the duct run as short and as straight as possible with as few turns as possible.

• Avoid sharp-angled turns. Instead, use smooth, gradual turns such as adjustable elbows or 45 degree

angled turns.

• Forductrunsover20feet,increasetheductdiameterbyoneinchforeverytenfeetofduct.

• A 90 degree elbow is equal to 5 feet of duct.

Termination Requirements

• Airowmustnotberestrictedattheendoftheductrun.

• A wall louver or roof jack is required for each duct run.

• Everywalllouverorroofjackmustincludeagravitydampertopreventbackdrafts.

• Do not use screen wire or spring-loaded doors on wall louvers or roof jacks.

• Donotterminateventingintoanatticorchimney.

Produktspecifikationer

Varumärke:	Vent-A-Hood
Kategori:	Fläktkåpa
Modell:	SLH9230SS
Enhetsplacering:	Ingebouwd
Typ av operation:	Touch
Färg på produkten:	Zwart
Inbyggd display:	Ja
Timer:	Ja
Vikt:	11900 g
Bredd:	590 mm
Djup:	520 mm
Höjd:	58 mm
Sladdlängd:	1 m
Barnlås:	Ja
Förpackningens vikt:	13500 g
Förpackningens bredd:	675 mm
Djuppackning:	620 mm
Förpackningshöjd:	125 mm
Brännare/kokzonseffekt 2:	1800 W
Brännare/kokzonseffekt 3:	1800 W
Brännare/kokzonseffekt 1:	1800 W
Antal brännare/kokzoner:	4 zone(s)
Typ av häll:	Inductiekookplaat zones
Antal gasbrännare:	0 zone(s)
Antal elektroniska kokzoner:	4 zone(s)
Kontrollposition:	Boven voorzijde
Ansluten last (elektrisk):	7200 W
Installationsfackets bredd:	560 mm
Installationsfack djup:	490 mm
Ansluten last (gas):	- W
Bredd på häll:	60 cm
Boost funktion:	Ja
Restvärmeindikator:	Ja
Pansigenkänning:	Ja
Brofunktion:	Ja
Brännare/kokzonseffekt 4:	1800 W
Strömkälla brännare/kokzon 1:	Electrisch
Strömkälla brännare/kokzon 2:	Electrisch
Strömkälla brännare/kokzon 3:	Electrisch
Strömkälla för brännare/kokzon 4:	Electrisch
Kookzone 1 boost:	2100 W
Kookzone 2 boost:	2100 W
Kookzone 3 boost:	2100 W
Kookzone 4 boost:	2100 W
Placera brännare/kokzon 1:	Links voor
Diameter brännare/kokzon 1:	210 mm
Placera brännare/kokzon 2:	Links achter
Brännare/kokzons diameter 2:	210 mm
Placera brännare/kokzon 3:	Rechts voor
Brännare/kokzons diameter 3:	210 mm
Placera brännare/kokzon 4:	Rechts achter
Brännare/kokzons diameter 4:	210 mm
Kokzon 1 form:	Rond
Kokzon 2 form:	Rond
Kokzon 3 form:	Rond
Kokzon 4 form:	Rond
Flexibel kokzon:	Ja
Flexibel kokzon 1 storlek (BxD):	220 x 400 mm
AC-ingångsspänning:	220 - 240 V
Inbyggd fläktkåpa:	Nee
Boost flexibel kokzon 1:	3600 W