Yakima LiteRider 3 Bruksanvisning
Yakima
Cykelhållare
LiteRider 3
Läs gratis den bruksanvisning för Yakima LiteRider 3 (5 sidor) i kategorin Cykelhållare. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 2 recensioner. Har du en fråga om Yakima LiteRider 3 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/5
IMPORTANT WARNING
IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER
ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR
TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS
PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND
UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.
FLAT WASHER (2X)
NUT (1X)
WRENCH (1X)
KEYS (2X)
2-ZIP STRIPS (6X)
LARGE HEX WRENCH (1X)
BOLT (1X)
3-ZIP STRIPS (9X)
SMALL HEX WRENCH (1X)
2BIKE (1X)
LONG STRAP (1X)
WHEEL STRAP (1X)
3 BIKE (1X)
PURCHASE SEPARATELY:
TubeTop: Required for bikes with step-through/
Ladies frames or bikes with slanted top tubes.
Part #8002531
Insert tongue into vehicle's hitch.
IF SPARE
TIRE CAUSES
INTERFERENCE,
DO NOT USE
THIS PRODUCT!
Align the holes in
the receiver to the
holes in the tongue.
If your vehicle's hitch is 1 1/4": remove the 2" hitch adapter.
For 2" hitches:
proceed to next step.
Install tongue.
•Install bolt and a flat
washer.
• Add a second
washer, attach nut.
Remove the
screw from the
adapter using
the small hex
wrench.
Secure tongue.
Remove the
adapter from
the tongue.
Join the tongue with the mast (with
mast tilted) aligning the holes as
shown. Assembly may be easier by first
installing tongue in vehicle's Hitch.
•Use the large hex
wrench and closed
wrench to tighten
completely.
Lock mast in the full upright position.
LiteRider mast must be
locked in the upright
position before loading
bikes or moving vehicle!
LOCKEDUNLOCKED!
Tighten locking knob.
NOTE: Lock must be in unlocked
position to tighten or loosen knob.
•Remove dirt guard.
•Turn key clockwise to unlock.
•Insert safety pin.
•TIGHTEN knob until there is
no more play between the
tongue and receiver.
•Lock it.
•Replace dirt guard.
NOTE: When
locked, the knob
will spin freely,
making it unable
to be loosened.
Safety pin
is required
for use.
Extend arms. Raise arms
completely.
Pull the lever to release
the arms from locked-
down position.
Arms will lock into
position.
CAUTION
Keep fingers away from
ALL moving parts!
A Yakima TubeTop (see cover
page) may be to carry required
your bike safely.
Failure to load
bikes properly can
result in property
damage, personal
injury, or death.
Always use
cradles closest
to vehicle.
Bikes should be as level as possible
to avoid ground clearance issues and
possible ejections.
Load heaviest bike first.
•Always load first bike with
chain away from vehicle.
•Compress stabilizers against
bike frame.
•Stabilize the bike frame in the
cradle. Arrange bikes for best
stabilization.
Produktspecifikationer
| Varumärke: | Yakima |
| Kategori: | Cykelhållare |
| Modell: | LiteRider 3 |
Behöver du hjälp?
Om du behöver hjälp med Yakima LiteRider 3 ställ en fråga nedan och andra användare kommer att svara dig
Cykelhållare Yakima Manualer
19 Oktober 2024
11 Oktober 2024
10 Oktober 2024
3 Oktober 2024
18 September 2024
29 Augusti 2024
28 Augusti 2024
21 Augusti 2024
21 Augusti 2024
19 Augusti 2024
Cykelhållare Manualer
- MFT
- Atera
- Spinder
- Buzz Rack
- LAS
- Scosche
- XLC
- Twinny Load
- UEBLER
- Bosal
- Enduro
- Thule
- Eufab
- Saris
- Bikemate
Nyaste Cykelhållare Manualer
1 April 2025
3 Februari 2025
26 Januari 2025
25 Januari 2025
8 Januari 2025
2 Januari 2025
30 December 2025
30 December 2025
30 December 2025
19 Oktober 2024