AMX VARIA-ACS-100F Bruksanvisning
AMX
Inte kategoriserad
VARIA-ACS-100F
Läs gratis den bruksanvisning för AMX VARIA-ACS-100F (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 13 recensioner. Har du en fråga om AMX VARIA-ACS-100F eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
QUICK START GUIDE
VARIA-ACS-80F 8” Fixed Tabletop Stand
VARIA-ACS-100F
10.1” Fixed Tabletop Stand
Overview
The Varia Fixed Tabletop stands are designed for 8” VARIA-80 & 10.1” VARIA-100
Touch Panels, and give them a sturdy & stylish fixed-angle tabletop solution
that’s reminiscent of AMX’s Modero touch panel family.
FIG. 1 Varia Touch Panel on Fixed Tabletop Stand
Model Availability & Compatibility
FIXED TABLETOP STANDS
VARIA-ACS-80F
(AMX-UMT0801)
VARIA-80 Touch Panel (AMX-UTP0811)
VARIA-ACS-100F
(AMX-UMT1001)
VARIA-100 Touch Panel (AMX-UTP1011)
VARIA-100N Touch Panel (AMX-UTP1011N)
Other Models Available
ANGLE-SELECT TABLETOP STANDS
VARIA-ACS-810A
(AMX-UMT8111)
VARIA-80 Touch Panel (AMX-UTP0811)
VARIA-100 Touch Panel (AMX-UTP1011)
VARIA-100N Touch Panel (AMX-UTP1011N)
VARIA-ACS-150A
(AMX-UMT1511)
VARIA-150 Touch Panel (AMX-UTP1511)
VARIA-150N Touch Panel (AMX-UTP1511N)
Installation
Varia Fixed Tabletop Stands are easily installed with the supplied hardware and
a Philips-head screwdriver.
1. Place the panel face-down on a soft cloth, and orient the panel so
that the top of the touch panel is closest to you.
FIG. 2 Varia Touch Panel, rear
2. If they are installed, remove two screws from the lower back cover.
Screw Locations
FIG. 3 Rear cover screws, if installed
3. Place your thumbs on the rectangular access holes, and push the
lower cover away from you. The lower cover can then be placed
aside; it is not used with the Fixed Tabletop Stands.
FIG. 4 Rear cover removal
4. Rotate the panel back around so the bottom is closest to you.
5. On the tabletop stand, remove the black plastic cover by sliding it
away from the aluminum base. It is held on by magnets. Then
unscrew the rubber pads from the base.
6. Install the aluminum base on the back o the touch panel.
Note: In most circumstances, the networking cable can be routed in
after base installation. However, category cables with bulky strain
relief and/or hoods over the RJ-45 connector may need to be installed
before the aluminum base.
FIG.5 Fixed Tabletop Stand, aluminum base, underneath
7. Attach the base with the four (4) supplied screws.
Top
Top
Produktspecifikationer
| Varumärke: | AMX |
| Kategori: | Inte kategoriserad |
| Modell: | VARIA-ACS-100F |
Behöver du hjälp?
Om du behöver hjälp med AMX VARIA-ACS-100F ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad AMX Manualer
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
27 December 2024
7 December 2024
25 September 2024
25 September 2024
24 September 2024
Inte kategoriserad Manualer
- Chapin
- IKEA
- Dunlop
- GR Bass
- Livn
- EPH Elektronik
- Whirlwind
- Elgato
- Omnitronic
- Hurricane
- Lynx Technik
- RAVPower
- ETiger
- SMC
- Pro-Lift
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025