ART USB Phono Plus Bruksanvisning

ART mottagare USB Phono Plus

Läs gratis den bruksanvisning för ART USB Phono Plus (11 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 3.7 stjärnor baserat på 11 recensioner. Har du en fråga om ART USB Phono Plus eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/11

USB Phono Plus

Audiophile Computer Interface

Project Series

USER’S MANUAL

IMPORTANT SAFETY INSTRUCTION – READ FIRST

This symbol, whenever it appears, This symbol, wherever it appears, alerts you

alerts you to the presence of uninsulated to important operating and maintenance

dangerous voltage inside the enclosure-voltage instructions in the accompanying literature.

that may be sucient to constitute a risk of shock. Please read the manual.

Read instructions:

Retain these safety and operating instructions for future reference. Heed all warnings printed here and on the

equipment. Follow the operating instructions printed in this user manual.

Do not open:

There are no user serviceable parts inside. Refer any service work to qualied technical personnel only.

Power sources:

Connect the units power supply to mains power only of the type described in this user manual or marked on

the power supply.

Power supply:

Use the power supply with sealed mains plug appropriate for your local mains supply as provided with the

equipment. If the provided supply does not t into your outlet consult your service agent. Route the power cord

so that it is not likely to be walked on, stretched or pinched by items placed upon or against it.

Grounding:

Do not defeat the grounding and polarization means of the power supply.

Moisture:

To reduce the risk of re or electrical shock do not expose the unit to moisture or use in damp or wet condi-

tions. Do not place container of liquid on unit.

Heat:

Do not locate the unit close to excessive heat or direct sunlight, as this could cause a re hazard. Locate the

unit away from any equipment, which produces heat such as: power supplies, power ampliers and heaters.

Environment:

Protect from excessive dirt, dust, heat, and vibration when operating and storing. Avoid tobacco ash, drink

spillage and smoke, especially that associated with smoke machines.

Handling:

Protect the controls from damage during transit. Use adequate padding if you need to ship the unit. To avoid

injury to yourself or damage to the equipment, take care when lifting, moving, or carrying the unit.

Servicing:

Unplug power immediately if equipment is exposed to moisture, the power supply becomes damaged during a

lightning storm or if smoke odor or noise is noted. Refer servicing to qualied technical personnel only.

Installation:

Install the unit in accordance with the instructions printed in the user manual.

INTRODUCTION

The USB Phono Plus

Project

Project Project Series

Series

SeriesSeries

is a high quality USB audio interface with a built-in phono

preamp. It acts as an interface between your computer and a wide variety of analog and digital

sources. The analog inputs are switchable between Phono and Line level signals and a Low Cut filter

removes rumble and wind noise while leaving the audio pristine. The front Gain Trim control and

Signal/Clip LED allow you to optimize the analog to digital converter for a wide range of input

sources. The front panel USB Monitor/headphone jack and the Optical Output on the rear panel can

monitor the audio output from your computer. The USB Monitor/headphone jack can also provide

zero latency monitoring of the input source for easy cueing of records and tapes. The built-in low

noise Phono Preamp circuit is highly accurate and precisely conforms to the RIAA standard. The Line

Out jacks are always connected to the input preamp signal for source monitoring or to allow use as a

stand-alone phono preamp.

Housed in an all aluminum black anodized case, the USB Phono Plus

Project

Project Project Se

SeSeries

ries

riesries

can be

snap. An Optical TOSLINK Input and Output as well as an S/PDIF Input let you use the USB Phono

Plus

Project Serie

Project Serie Project Series

as a digital audio to USB interface as well.

The USB Phono Plus

Proje

ProjeProject

ct ct Series

Series

SeriesSeries

is fully compliant with the USB 2.0 specication and uses

USB adaptive mode for playback and USB asynchronous mode for recording. The USB Phono Plus

Project

ProjectProject

Series

SeriesSeries

interface uses the standard “USB Audio CODEC”. This driver is built into most

modern operating systems, including most current versions of Linux. Since some details of how the

audio interface is set vary with dierent versions of Linux, the setup is beyond the scope of this

document. The main key in setup is to look for “USB Audio CODEC” as the recording source or

playback monitor output while the USB Phono Plus

Project

Project Project series

series

seriesseries

is connected. No special

drivers are needed. We’ve included a CDROM containing the user manual and Audacity recording

software to get you started!

Key Features Include

• USB Connectivity to Desktop and Laptop Computers

• RIAA Accurate Low Noise Phono Preamp

• Up to 45 dB of Clean Gain

• Latency Free Monitoring

• S/PDIF or optical to USB and USB to Optical Interfaces Included

• Preamp Line Out Allows Use as a Stand-alone Phono Preamp

• Includes Audacity Recording Software

• Compact, Stackable all Aluminum Chassis

• Flexible Power from USB or External Power Supply

• Three Year Warranty

Produktspecifikationer

Varumärke:	ART
Kategori:	mottagare
Modell:	USB Phono Plus
Färg på produkten:	Zilver
Vikt:	3100 g
Strömförsörjning:	AC 220-240V
Ljudsystem:	Nicam
Strömförbrukning (i standby):	1.3 W
Anslutningar:	2nd Scart, Additional Audio Out, In / Decoder, RF In/Out, Scart
Antal huvuden:	4
Uppspelningsformat:	SP, LP, SLP
Mått (B x D x H):	430 x 255 x 96 mm
Fjärrkontroll ingår:	Ja
Strömförbrukning (typiskt):	17 W