BlendMount MTX-1010 Bruksanvisning
Sidor 2 Engels Detektor
Läs bruksanvisningen för BlendMount MTX-1010 gratis online eller ladda ner PDF:en. 25 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
Guidelines on Using a Voltmeter to
Locate Power and Ground
1. First set your voltmeter to the continuity
setting ( should beep when you touch the red
and black probes together, telling you they are
shorted).
2. Find a ground on the car somewhere, like a
bolt under the dash, or a metal cross member.
3. Put the black probe on that ground, and
touch the back
of
each exposed wire connector
in the mirror harness with the red probe.
4. For each wire that beeps, that means that
wire is grounded. Tum the ignition to the on
position, then back to off, and make sure it
beeps regardless
of
the ignition position.
5.
Put the voltmeter into VDC mode, to
measure DC volts, turn the ignition to the on
position.
6.
Put the black probe on the ground wire
found
in
#4.
7.
Touch each
of
the wires
in
that harness with
the red probe, and note which one( s) gives you
+12-14 volts, turn the ignition off to verify that
the volt readings go down to zero or close to
zero.
"Power Up" Your Radar Detector
by
TAPPING Into Your
Rear View Mirror's Wire Harness
\
2 Amp in line fuse
Innovative Design
And
Precision Manufacturing
Manufactured in
USA
©2016 J28 Design Inc.
WWW
.MIRRORTAP.COM
MTX
Series
12 Volt Radar Detector Power Cord
With In Line Fuse
1 O"
OVERALL LENGTH
RJ11
CONNECTOR
Produktspecifikationer
| Varumärke: | BlendMount |
| Kategori: | Detektor |
| Modell: | MTX-1010 |
| Färg på produkten: | Zwart |
| Förpackningens vikt: | 780 g |
| Snäll: | AV-receiver |
| LED-indikatorer: | Stroom |
| Maximal upplösning: | - Pixels |
| Förpackningsmått (BxDxH): | 181 x 62 x 241 mm |
| Certifiering: | CE, c-UL, UL, C-tick, FCC Class A, ICES, VCCI |
| Analog signalformat: | NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Impedans: | 75 Ohm |
| Förvaringstemperatur: | -40 - 70 °C |
| Förvaringsfuktighet: | 10 - 90 procent |
| Rackmontering: | Ja |
| Utström: | 0.2 A |
| BNC utgångsportar: | 1 |
| Mottagare mått (B x D x H): | 56 x 76 x 42 mm |
| RJ-45 ingångsportar: | 1 |
| Maximal-räckvidd: | 300 m |
| AC-ingångsspänning: | 100-240 V |
| AC-ingångsfrekvens: | 50 Hz |
| Drifttemperatur (TT): | 0 - 50 °C |
| Relativ luftfuktighet i drift (VV): | 10 - 90 procent |
| Driftspänning (mottagare): | 12 V |
| Mottagarens vikt: | 500 g |
| Kabeltyper som stöds: | Cat5, Cat5e, Cat6 |
| 3,5 mm utgång: | Ja |
Behöver du hjälp?
Om du behöver hjälp med BlendMount MTX-1010 ställ en fråga nedan och andra användare kommer att svara dig
Detektor BlendMount Manualer
BlendMount MT-1010 Bruksanvisning BlendMount BMG-2001R Bruksanvisning BlendMount MT-1015 Bruksanvisning BlendMount BBE-2001R Bruksanvisning BlendMount MTX-2020 Bruksanvisning BlendMount HT-1096 Bruksanvisning BlendMount MTX-2015 Bruksanvisning BlendMount HT-2096 Bruksanvisning
Alla BlendMount Detektor manualer
Populära i Detektor
BlendMount BR7-2001R Bruksanvisning BlendMount MTX-2010 Bruksanvisning BlendMount MTX-1015 Bruksanvisning
Detektor Manualer
Nyaste Detektor Manualer
Satel AQUA Pet 2E Bruksanvisning Milwaukee LED 3202-20 Bruksanvisning Satel OPAL Plus Bruksanvisning Satel TOPAZ Bruksanvisning Satel AMBER Bruksanvisning Satel TOPAZ Pet Bruksanvisning Satel AQUA Plus Bruksanvisning Garrett Vortex CSI Bruksanvisning Satel AMBER 2E Bruksanvisning Satel NAVY Bruksanvisning