Chamberlain 041C4672 Bruksanvisning

Chamberlain Inte kategoriserad 041C4672

Läs gratis den bruksanvisning för Chamberlain 041C4672 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 1.5 recensioner. Har du en fråga om Chamberlain 041C4672 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

To avoid SERIOUS INJURY or DEATH from electrocution,

disconnect power to opener BEFORE proceeding.

RPM SENSOR 41C4672

Replacement Instructions

You will need a 1/4" magnetic nut driver and

long-nosed pliers.

1. Disconnect power to the opener.

2. Remove the opener lens (refer to your owner’s manual).

3. Remove the cover:

• Using a 1/4" magnetic nut driver, remove the two

screws recessed in the bottom of the cover.

• Unplug the wires to the light sockets inside, and place

the cover aside.

4. Lift off the Control Center access door and set aside.

5. Unfasten the receiver logic board assembly from the

chassis by removing the two screws inside the panel

under the top edges (a). Allow it to hang suspended by

wires.

6. Disengage the limit switch assembly from the(b)

retention slots in the limit switch bracket (c) by

squeezing the top and bottom on the right near the drive

gear (see illustration).

7. Disengage the hook on the left and allow assembly(d)

to hang by wires.

8. Remove the screw at the top rear of the limit switch

bracket where it fastens to the chassis.

9. Tilt the bracket upwards to disengage its two hooks

from slots in the chassis, and allow it to hang.

10. Remove the worm gear and retainer (e):

• Spread the retainer wings slightly to disengage from

the worm gear and slide the retainer center pin out

from the aperture in the motor shaft.

• Pull out the worm gear.

11. Pull out the interrupter cup (f).

12. Pull out the wire harness assembly plug from the(g)

sensor assembly .

13. Remove the sensor assembly (h) from the motor

bracket:

• With long-nosed pliers, squeeze one of the two

retainer prongs protruding through the motor bracket

(i) while lightly pulling away the sensor assembly to

free the prong from its hole. (This works best when

the pliers are held as vertically as possible.)

• Repeat with the second prong.

• Unhook and discard the old sensor assembly.

14. Install the new sensor assembly:

• Place the retaining hook over the edge of the slot in

the motor bracket.

• Align prongs with holes and snap the assembly in

place.

15. Plug the wire harness into the new sensor.

16. Replace the interrupter cup, pushing it all the way to the

end of the motor shaft, against the collar.

17. Reverse steps 10-1 to reassemble the unit and

reconnect power.

NOTE: A test of the safety reverse system is necessary for

safe operation. Follow the instructions on the reverse or in

your owner’s manual.

WARN

WARNWARNING

ING

INGING

(squeeze)

1-1/2" (3.8 cm) board

(or a 2x4 laid flat)

Test the Safety Reversal System

TEST

• With the door fully open, place a 1-1/2" (3.8 cm) board

(or a 2x4 laid flat) on the floor, centered under the

garage door.

• Operate the door in the down direction. The door must

reverse on striking the obstruction.

ADJUST

• If the door stops on the obstruction, it is not traveling

far enough in the down direction. Increase the DOWN

limit by turning the DOWN limit adjustment screw

counterclockwise 1/4 turn.

NOTE: On a sectional door, make sure limit

adjustments do not force the door arm beyond a

straight up and down position.

• Repeat the test.

• When the door reverses on the 1-1/2" (3.8 cm) board,

remove the obstruction and run the opener through 3 or

4 complete travel cycles to test adjustment.

• If the unit continues to fail the Safety Reverse Test, call

for a trained door systems technician.

IMPORTANT SAFETY CHECK:

Test the Safety Reverse System after:

• Each adjustment of door arm length, limits, or force

controls.

• Any repair to or adjustment of the garage door

(including springs and hardware).

• Any repair to or buckling of the garage floor.

• Any repair to or adjustment of the opener.

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED

or KILLED by a closing garage door.

• Safety reversal system MUST be tested every month.

• If one control (force or travel limits) is adjusted, the other

control may also need adjustment.

• After ANY adjustments are made, the safety reversal system

MUST be tested. Door MUST reverse on contact with 1-1/2"

high (3.8 cm) object (or 2x4 laid flat) on the floor.

WARN

WARNWARNING

ING

INGING

Produktspecifikationer

Varumärke:	Chamberlain
Kategori:	Inte kategoriserad
Modell:	041C4672
Enhetsplacering:	Onderbouw
Typ av operation:	Touch
Inbyggd display:	Ja
Vikt:	45311 g
Bredd:	598 mm
Djup:	573 mm
Höjd:	815 mm
Nettoskatt:	2400 W
Antal platsinställningar:	14 couverts
Torksystem:	Warmtewisselaar
Dörrfärg:	Roestvrijstaal
Sladdlängd:	1.75 m
Fördröjd starttimer:	Ja
Startfördröjning:	24 uur
Indikering av återstående tid:	Ja
Wi-Fi-kontroll:	Ja
Cykelns längd:	275 min
Ljudnivå:	42 dB
Energie-efficiëntieklasse:	D
Belysning inuti:	Ja
Vattenförbrukning per cykel:	9.5 l
Nuvarande:	10 A
Självrengörande:	Ja
Bulleremissionsklass:	B
Antal tvättprogram:	8
Energiförbrukning per 100 cykler:	85 kWu
Produktstorlek:	Volledige grootte (60 cm)
Färgkontrollpanel:	Zwart
Doseringsassistent:	Ja
Automatisk detektering av tvättmedel:	Ja
AquaStop-funktion:	Ja
Glasskydd:	Ja
Halvlastad:	Ja
Belastningssensor:	Ja
Tvättprogram:	Auto 45-65°C, Eco 50°C, Glass/delicate, Intensive 70°C, Pre-wash, Quick
Energiförbrukning per cykel:	0.93 kWu
Avloppsslangens längd:	1.9 m
Vattentillförselslangens längd:	1.65 m
Övre korg justerbar höjd:	Ja
Temperatur (max):	60 °C
Energieffektivitetsskala:	A tot G