Cotech 52008x36 Bruksanvisning


Läs gratis den bruksanvisning för Cotech 52008x36 (6 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 5.5 recensioner. Har du en fråga om Cotech 52008x36 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/6
UNITED KINGDOM CUSTOMER SERVICE
tel 020 8247 9300 customerservice@clasohlson.co.uk www.clasohlson.co.uk 10 13 Market Place, Kingston upon Thames, Surrey, KT1 1JZe-mail internet postal
Ver. 20181211
Outdoor IP44 Receiver Switch
Art.no 36-6013 Model 52008x36
Please read theentire instruction manual before using theproduct
and then save it for future reference. We reserve theright for
any errors in text or images and any necessary changes made
to technicaldata. In theevent of technical problems or other
queries, please contact our Customer Services.
Safety
Make sure that theelectrical socket that theproduct
is plugged into is easily accessible in case it and
theconnected product need to be quickly disconnected
from themains electricity.
Do not connect products of this type to each other.
Do not cover theproduct.
Note: Thelight can also be switched on/off manually by
pressing thebutton on thereceiver.
Unpairing all paired transmitters
1. Hold in thebutton on thefront of thereceiver for 6seconds
until theLED button starts flashing quickly.
2. When theLED stops flashing, all thetransmitters which
were paired with it will have been unpaired.
Unpairing one paired transmitter
1. Hold in thebutton for 3 seconds on thefront of thereceiver
you wish to unpair and then release.
2. TheLED button will start flashing slowly. Thereceiver is now
ready to unpair from thetransmitter.
3. Press in the [ OFF ] button on thetransmitter (make sure
to choose thecorrect [ OFF ] button if thetransmitter can
connect to multiple receivers). Thetransmitter will now
unpair from thereceiver.
Care and maintenance
Thereceiver should be unplugged from thewall socket if it
is not to be used for alongtime.
Thereceiver should be cleaned by wiping it with adrycloth.
Troubleshooting guide
Thereceiver is
not working,
theLED is
notlit.
Has thereceiver been paired with
atransmitter as describedabove?
Trypairing themagain.
Check that thelight is properly plugged
into thereceiver and that it is switched
on and not faulty.
Try plugging thelight into another electrical
outlet to make sure that itworks.
Is there electricity at theoutlet where
thereceiver is pluggedinto?
Responsible disposal
This symbol indicates that this product should
not be disposed of with general household
waste. This applies throughout the entire EU.
In order to prevent any harm to the environment
or health hazards caused by incorrect waste
disposal, the product must be handed in for
recycling so that the material can be disposed
of in a responsible manner. When recycling
your product, take it to your local collection facility or contact
the place of purchase. They will ensure that the product is
disposed of in an environmentally sound manner.
1. Plug thereceiver into anelectrical
outlet.
2. Hold in thebutton on thefront of
thereceiver for at least 3 seconds
and then releaseit.
3. Thebutton’s LED will begin
flashing slowly. Thereceiver is
now ready to be paired with
atransmitter.
4. Pair thereceiver to thetransmitter
by following theinstructions
accompanying your transmitter.
Upto 6 transmitters can be paired
with thereceiver.
5. Plug alight into thereceiver and
check that it is turnedon.
6. Thelight can now be controlled by
using atransmitter.
Operation
Installation
Specifications
Mains power supply 230V AC, 50Hz
Frequency 433.92 MHz
Maxrange 25m
Load (resistive bulb) 0–3680W
Load (inductive) 0–613W


Produktspecifikationer

Varumärke: Cotech
Kategori: Inte kategoriserad
Modell: 52008x36

Behöver du hjälp?

Om du behöver hjälp med Cotech 52008x36 ställ en fråga nedan och andra användare kommer att svara dig