Danfoss TP5000 Si Bruksanvisning
Läs gratis den bruksanvisning för Danfoss TP5000 Si (2 sidor) i kategorin Termostat. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 3.5 stjärnor baserat på 6.5 recensioner. Har du en fråga om Danfoss TP5000 Si eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Fig.1
TP5000 Si/TP5000 RF Si
User Instructions
Mon-Fri Sat-Sun
Fig.2
Before programming the thermostat press and release the RESET button to restart
the unit. (Fig. 1)
Setting the Clock and Day
The day and time are set in the factory and therefore it will not normally be necessary
to do this on site. Changes between summer and winter time are handled automatically
by the unit.
Accepting the Factory Pre-settings
The TP5000 Si has pre-set times already programmed in, which often suit most people
(see table below).
Note: If set up for 4 events per day, events 3 & 4 are skipped. If set up for 2 events per
day, events 2, 3, 4 & 5 are skipped and the events are re-numbered.
To adjust the factory pre-settings & set your own time and temperature
programmes
For Days 1-5 (weekdays)
a) Press PROG (Fig. 2) until the 1st pre-set time and temperature (Event 1 Days 1,2,3,4,5)
(Fig. 3).
b) Use + or – buttons (Fig. 4) to adjust the TIME (press and hold to change in 10 min
increments).
c) Use Λ or V buttons (Fig. 5) to adjust the TEMPERATURE.
d) Press PROG (Fig. 2) to move to next preset time & temp (Event 2) (Fig. 6).
e) Repeat steps b, c & d for programming Events 3, 4, 5 & 6.
For Days 6-7 (weekends)
Press •PROG (Fig. 2) to show 1st pre-set time and temperature (Event 1 Days 6-7)
(Fig. 7).
Repeat steps b, c and d above to programme time and temperature events for •
the weekend.
Returning to RUN mode
Press PROG (Fig. 2) – the colon in the LCD display will start to flash (Fig. 8).
Fig.5
Fig.4
Fig.6
Fig.7
Fig.8
Event Time Temp. °C
1 06:30 20
2 08:30 15
3 11:30 20
4 13:30 15
5 16:30 21
6 22:30 15
Event Time Temp. °C
1 07:30 20
2 09:30 20
3 11:30 20
4 13:30 20
5 16:30 20
6 22:30 15
RESET
Fig.3
Complete Shut off - Summer time
Press Λ and V together to enter thermostat mode. A frost protection symbol (snowflake in a
shield) will appear in the display . Press the down arrow ∨ once, OFF will appear in the display.
To return to automatic programming press both ∧ and ∨ together.
Produktspecifikationer
| Varumärke: | Danfoss |
| Kategori: | Termostat |
| Modell: | TP5000 Si |
Behöver du hjälp?
Om du behöver hjälp med Danfoss TP5000 Si ställ en fråga nedan och andra användare kommer att svara dig
Termostat Danfoss Manualer
7 September 2025
7 September 2025
6 September 2025
6 September 2025
6 September 2025
6 September 2025
6 September 2025
6 September 2025
6 September 2025
6 September 2025
Termostat Manualer
- Nefit
- Honeywell
- THERMAFLEX
- Bosch
- AWB
- Heatit
- Cepra
- Coati
- Ferroli
- Easy Timer
- Zehnder
- Levoit
- Jumo
- Heatmiser
- OJ ELECTRONICS
Nyaste Termostat Manualer
13 Oktober 2025
12 Oktober 2025
12 Oktober 2025
5 Oktober 2025
2 Oktober 2025
2 Oktober 2025
29 September 2025
28 September 2025
28 September 2025
28 September 2025