DPW Design Mix Bruksanvisning
Läs gratis den bruksanvisning för DPW Design Mix (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 28 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 14.5 recensioner. Har du en fråga om DPW Design Mix eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Mix
The Mix is a compact 4 channel stereo mixer that also can be set up to be set up to be up to 8
channels of mono with crossfading in 4 groups. It also has a built in soft knee limiter for subtle level
control or harder creative coloring of the sound.
It is designed to be a flexible compact part of your system. As the main mixer for a small system or
you have a few distributed in your bigger system and use one to collect the signals from all of them
sa the main out.
The unit can be used as a utility module for control voltages as well as for audio. It is DC coupled.
Inputs, stereo mode
There are 4 channels of stereo input with volume and pan control.
When using one of the channels with mono in stereo mode you can
connect to either left or right channel. The left and right inputs are
normalled to each other.
All channels have one time amplification (unity gain) when the Vol
knob is turned fully clockwise.
The module is designed to never clip internally but the levels can get
high at the output stage. So the output stage has a controlled nice
sounding round clipping that limits the output to +/- 10V.
Use the output LEDs as a guide to get an output level that doesn't
clip.
The bandwidth of the module in this mode is 150 kHz (-3dB point) so
there is basically no unwanted frequency dependent phase shift in the
audio range.
The extended bandwidth will also make the sound of the mixer very
transparent.
M switches
The M switches (mono) turns the channels left and right input to dual
mono with the Vol knob as a volume for both and the Pan becomes a
mono crossfade between the left and right input.
The M switches affects the channels in two groups. The upper M switch affects channel 1 and 2.
the lower affects channel 3 and 4.
This means that engaging one or two M switches can give you 4 mono with two groups of
crossfade plus two stereo channels or 8 channels of mono with 4 groups of crossfade.
The crossfade can be used as a performance feature to gradually crossfade from one part of your
system to an other or to build more complex voices.
If only one side of a channel is connected, the M switch for that channel is on and Pan is in center
possition you will get a two times amplification of that channel. Can be used for extra boost where
needed.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-M1 Rev B
Produktspecifikationer
| Varumärke: | DPW Design |
| Kategori: | Inte kategoriserad |
| Modell: | Mix |
Behöver du hjälp?
Om du behöver hjälp med DPW Design Mix ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad DPW Design Manualer
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
Inte kategoriserad Manualer
- Selleys
- QNAP
- Wamsler
- Maxxter
- Cybex
- Lehle
- Real Cable
- NEXTO DI
- Point 65
- Sanofi
- Sun Pumps
- Fakir
- Medeli
- Easypix
- Plum
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025