DPW Design Switch Bruksanvisning

DPW Design Inte kategoriserad Switch

Läs gratis den bruksanvisning för DPW Design Switch (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 12.5 recensioner. Har du en fråga om DPW Design Switch eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Switch SW-1, Quad bidirectional switch

The SW-1 is a four individual bidirectional switch module in Eurorack format with manual or CV control over

the switches.

Bidirectional means that signals can flow in both directions through the switches. You can send signals in to

1 and out on 1G or 1R. Or you can send signals in on 1G and 1R and 1 will be the output.

The switches can be latched in pairs. The layout is for ergonomics when switching stereo buses.

Control of the switches with CV can be done up to well above 100 kHz.

This opens for interesting wave shaping as you can switch out a piece of a cycle of an audio rate signal and

replace it with something else, wave splicing. Or change/swap places of your modules in your signal chain at

up to high or above audio rate.

Controls

The switch field is organized as rows of jacks, 1 to 4. The yellow lines on the front

panel shows which jacks that are connected to switches 1 to 4.

Above that field there is a picture showing the switch functionality as a schematic.

When the switch is unaffected by the LED-switch and CV, the in/out jack to the left is

connected to the in/out jack below the G. Where G correspond to green on the

channels LED-switch.

When the switch is affected by the LED-switch or CV, the in/out jack to the left is

connected to the in/out jack below the R. Where R correspond to red on the

channels LED-switch. Both the manual switch and the CV works as a gate signal.

If a channel is controlled via CV you can be temporarily override that by pressing

the channels LED-switch and fix it to be connected to R as long as you hold the

LED-switch. When released it will go back to CV control.

This way you can manually affect automated switching during a performance.

LED-switch 1 to 4 are momentarily switches when Latch is off.

When Latch is on the LED-switches will be toggling on/off when pressed.

Latch affects switches in pairs. 1 and 2 together and 3 and 4 together as

shown on the front panel graphics.

CV control works just like the switches. When a CV signal is high the switch is on.

A high signal is about 0,7V and works with any logical or audio signal up to well

above 100kHz. CV works like a gate signal. As long as CV is high the in/out jack will

be connected to R.

CV with Latch on. When Latch is on the switch will toggle on or off at every positive flank of the CV signal.

This can be used to flip the switch at a pulse from a sequencer.

It can also be used to add a subharmonic at audio rate switching as the switch toggles every second positive

flank.

Device specs

Module size: 8 hp wide, 29 mm deep with power connector.

Input impedance: 100 kohm

Through impedance: 20 ohm

Max trough current: 30 mA

Power requirements: +12V. Max power consumption 30 mA

-12V. Max power consumption 5 mA

Connect the power cable with the red stripe (-12V) down.

The unit is protected for reverse power.

DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden

www.dpw.se MAN-SW-1 Rev D

Produktspecifikationer

Varumärke:	DPW Design
Kategori:	Inte kategoriserad
Modell:	Switch
Färg på produkten:	Wit
Inbyggd display:	Nee
Bredd:	47 mm
Djup:	14 mm
Höjd:	48 mm
Snäll:	Draagbaar/Aan de muur gemonteerd
Internationell säkerhetskod (IP):	IP20
LED-indikatorer:	Nee
Monteringsmetod:	Inbouwmontage
Typ av strömkälla:	AC
Certifiering:	CE, RoHS
Gränssnitt:	RF Draadloos
Inspänning:	230 V
Frekvens:	868 MHz
Antal kanaler:	2 kanalen
Maximalt utomhusbereik:	100 m
Drifttemperatur (TT):	-5 - 45 °C
Typ produkt:	Schakelactor/dimactor
Installationsdjup:	15 mm
Potentialfri utgång:	Ja