DSC WS4938 Bruksanvisning
DSC
Fjärrutlösare
WS4938
Läs gratis den bruksanvisning för DSC WS4938 (2 sidor) i kategorin Fjärrutlösare. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6.5 recensioner. Har du en fråga om DSC WS4938 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
WS4938 Wireless Panic Button
Operating Instructions
Introduction
The WS4938 Wireless Panic Button was designed to transmit an emer-
gency signal from any location within the range of the alarm system,
regardless if the system is armed or disarmed.
The button is small and lightweight enough to be placed in a shirt pocket
or tucked away inside a purse. It can also be used with the supplied neck
strap or multi-functional clip - which can connect to your belt, car visor or
be permanently mounted to a convenient location.
To activate, press and hold the button for approximately 2 seconds.
The LED located on the top of the unit will light up to confirm a signal
has been sent.
NOTE: Signals will not be received if the button is not within range of the wireless receiver.
Activating, Enrolling and Programming
To conserve battery power the button comes deactivated. To activate sim-
ply remove the cover and slide the switch to the ON position (to the left).
This device is supervised. If the unit is removed from the coverage range a
trouble will be indicated on the system. If this is not desired, the supervisory bit
for this zone can be disabled on the receiver.
NOTE: For UL Listed installations, the supervisory bit in the receiver must be
enabled.
The following outlines the basic steps for programming and enrolling this
device on PowerSeries receivers.
For additional options or for other receivers please refer to the specific
receiver installation manuals.
Step 1 - Program Electronic Serial Number (ESN)
Section [804], subsections [01] - [32]
[01] Zone 1 |______|______|______|______|______|______| ... [32] Zone 32 |______|______|______|______|______|______|
Enter the 6 digit ESN located on the back of the device into the next available zone slot.
Step 2 - Program Zone Definition
Section [001] - [004]
Define the selected zone number with appropriate zone type [e.g., 24hr Panic (16),
24hr Holdup (12), 24hr Medical (15)]
Step 3 - Enable Wireless Zone Attribute
Section [101] - [132]
Turn Option [8] ON (wireless zone attribute) in corresponding zone attribute section
Step 4 - Enable/Disable Supervision (default is enabled)
Section [804], subsections [82] - [85]
[82] Wireless Zone Supervision (Zones 1- 8)
Default = ON
[83] Wireless Zone Supervision (Zones 9-16)
[84] Wireless Zone Supervision (Zones 17-24)
[85] Wireless Zone Supervision (Zones 25-32)
OPTION ON OPTION OFF
|_________| Option 1 Zone 01 Supervision Enabled Disabled
.
..
..
.
|_________| Option 8 Zone 08 Supervision Enabled Disabled
ON
Produktspecifikationer
| Varumärke: | DSC |
| Kategori: | Fjärrutlösare |
| Modell: | WS4938 |
Behöver du hjälp?
Om du behöver hjälp med DSC WS4938 ställ en fråga nedan och andra användare kommer att svara dig
Fjärrutlösare DSC Manualer
8 September 2024
23 Augusti 2024
10 Augusti 2024
2 Augusti 2024
Fjärrutlösare Manualer
- Cactus
- Angler
- Quantum
- Nissin
- Fujifilm
- Abus
- Multiblitz
- Godox
- Bolt
- Elinchrom
- Chamberlain
- Profoto
- Phottix
- Liftmaster
- Somfy
Nyaste Fjärrutlösare Manualer
20 Oktober 2025
16 Oktober 2025
12 Oktober 2025
10 Oktober 2025
10 Oktober 2025
23 September 2025
17 September 2025
24 Augusti 2025
23 Augusti 2025
23 Augusti 2025