Emko Eco PID Bruksanvisning

Läs gratis den bruksanvisning för Emko Eco PID (4 sidor) i kategorin Temperaturregulator. Guiden har ansetts hjälpsam av 40 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 2 recensioner. Har du en fråga om Emko Eco PID eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

3

2

1

4

5

6

Eco PID+, PID Temperature Control Unt�

- 4 dgt process (PV) and 4 dgt set (SV) dsplay�����

- Temperature sensor �nput (TC,RTD)

- Programmable ON/OFF, P, PI, PD and PID control forms

- Adaptaton of PID Coeffcents to the system wth Self-Tune and Auto-Tune ����

- Programmable Heatng or Coolng Functons for Control Output ���

- Selectable Alarm Functons for Alarm Output�

- Seral RS485 Communcaton (optonal)����

Introduct�on Brochure. ENG EcoPID+ 01 V00 03/22

Easy Access Dagram For Program Parameters�

Panel Mountng�

Enter Password wth ncrement��

or decrement buttons.

Approve password

wth Enter button�

Password Screen

Eco seres temperature controllers are desgned for measurng and controllng a ����

temperature value. They can be used n many applcatons wth ther TC and RTD �����

temperature measurement nput, mult-functon control outputs, selectable alarm ���

functons.�

They are manly used ��n glass, plastc, petro-chemstry, textle, automotve and machne �����

producton ���ndustres. Accurate and advanced controllng ��s performed wth selectable �

ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID functons.�

SPECIFICATIONS

Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)

Thermoresstance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)�

Measurement Range: Please refer to process �nput type selecton ��n process menu

parameters secton.�

Accuracy:

Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, whch one ��s greater) ±1 dgt max. ��

Thermoresstance (RTD):( ± 0.25% of full scale or ± 2ºC, whch one ���s greater) ±1 dgt ��

max.

Cold Juncton Compensaton:��Automatcally ±0.1°C/1°C�

Lne Compensaton:��Maxmum 10 Ohm�

Sensor Break Protecton:�Upscale

Samplng Cycle: �0.1 second

Input Flter:�Programmable

Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)

OUTPUT

Process Output:Relay (5A@250V at resstve load) or SSR Drver Output V���

(Maxmum 10mA, Max. 12V )�Z

Alarm Output:Relay (5A@250V at resstve load)V��

SUPPLY VOLTAGE (It must be determned ��n order)

230V (±15%) 50/60Hz - 4VAV

115V (±15%) 50/60Hz - 4VAV

100-240V 50/60Hz - 4VAV

24V(±%15) 50/60Hz - 4VAV

24V (±%15) 50/60Hz - 4VAW

10...30V - 4W Z

DISPLAY

Process Dsplay:�16 mm Red 4 dgt LED Dsplay���

Set Value Dsplay:�9 mm Orange 4 dgt LED Dsplay���

Led Indcators:�PO1 (SSR Process Output Status Led), PO2 (Relay

Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),

ºC, ºF LEDs

ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS

Operatng Temperature:�0...50ºC

Humdty :��0-90%RH (none condensng)�

Mechancal Impacts: �1Joule (IK06)

Protecton Class: �NEMA 4X (IP65 at front, IP20 at rear)

Weght:�150 gr.

Dmenson:��48 x 48 mm, Depth: 86,5 mm

Panel CutOut:46 x 46 mm

*1 - ON/OFF Hysteress parameter s not actve unless parameter s set as .����

*2 - Soft Start parameters( , , ) s not actve unless parameter s set as .���

*3 - Soft Start Control Output and Soft Start Control Tme parameters s not actve f parameter����

s set as .�

*4 - PID control parameters are not actve unless parameter s set as .��

*5 -Alarm-2 parameters are not actve f parameter s set as .���

*6 - Communcaton parameters are not actve on devces have no communcaton module.������

*7 - If s dfferent from 0 and user enters to program menu wthout enterng the password����

P

rot menu s not shown.�

Note: User can ext from any parameter screen wthout savng the values by pressng button. If ����

no operaton for 120 seconds, devce automatcally return to man screen. ����

Easy Access Dagram For Sensor Break Output�

Value From Man Screen�

Change the sensor break

output value wth ncrement��

or decrement buttons.

Press Enter button to save

new sensor break output value

and ext.�

Man ScreenMan Screen��

Note1: User can ext from parameter screen wthout savng the ���

values by pressng button. If no operaton for 120 seconds, devce ���

automatcally exts from parameter screen.��

Note2: Sensor break output value can be adjusted on programmng �

secton too.�

Tune Operaton�

Startng the Tune operaton��

1- Enter to the parameter n menu and select �

or ,then press button for savng parameter and turn to man ��

screen. Or easly press button for 3 seconds* n man screen.���

2- Observe that blnks n set dsplay.���

*Only Self Tune can be started by ths way.�

Cancelng Tune operaton:��

1- If sensor breaks;

2- If tune operaton can not be completed n 8 hours;��

3- Whle heatng self tune s runnng, f process value becomes �����

greater than process set value;

4- Whle coolng self tune s runnng, f process value becomes less �����

than process set value;

5- Whle tune operaton s runnng, f user changes the process set �����

value;

6- Whle tune operaton s runnng, f user changes the �����

parameter n menu; �

Then tune operaton s canceled, devce contnues to run wth former �����

PID parameters wthout changng PID parameters.��

PID TEMPERATURE CONTROL UNIT

PID+

Eco

Dmensons��

48 mm / 1.89 nch�

48 mm / 1.89 nch�

6 mm / 0.24 nch�

80,52 mm / 3.17 nch�

Maxmum 9 mm / 0.35 nch��

1-Before mountng the devce n your panel, ���

make sure that the cutout s of the rght sze.���

2- Check front panel gasket poston.��

3-Insert the devce through the cutout. If the �

mountng clamps are on the unt, put out them ��

before nsertng the unt to the panel.���

4-Insert the mountng clamps to the two of �

desgnated holes that located four sdes of ��

devce. �

5-Drag the mountng clamps n drecton 5 ����

untl the devce completely mmoble wthn the ������

panel.

6-In order to remove devce push on the �

mountng clamp as shown wth arrow 6 and ��

pull back.

Access and Change Set Values

Press ncrement or decrement�

button to change process set value.

Press Enter button to save new

set value and return the man screen.�

Man ScreenMan Screen��

Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS:40000

a

Note-1:User can ext from set value secton wthout savng the values by pressng button. If no �����

operaton for 120 seconds, devce automatcally exts from Set Value secton.�����

Note-2: Set value can be adjusted between Set Value Low and Hgh Lmt ( - ).���

Press Program button

to access password screen.

Electrcal Wrngs���

Toreducetheeffectofelectrcalnoseondevce,lowvoltagelne(especallysensor�����

������nput cable) wrng must be separetely from hgh current and voltage lne. If possble,

usesheldedcableandsheldmustbeconnectedtogroundonlyonesde.���

c

Note-1: External Fuse s recommended.�

Note-2: Stranded cable cross secton: 1,5mm², Sold cable cross-secton: 2,5mm²���

The strppng length s 7mm to 9mm.���

Note-3: Supply cables must comply wth the requrements of IEC 60277 or IEC 60245.��

It s advsed to use a two-pole supply swtch, desgnated for ths devce, wth open/�������

closed postons marked, n order to cut the power. It must be placed on the supply ���

���nput of the devce at a place where the user can easly reach.

V External fuse must be on phase connecton of the supply nput.��

Z External fuse must be on (+) lne connecton of the supply nput.���

Make sure that the power supply voltage range s sutable for the devce.���

Swtch on the power supply onlyafter all the electrcal connectons are n place.����

1

2

3

4

5

6

7

8

9

10

11

12

13

14

PO1

(Process Output 1)

SSR Output

12V

Max. 10mA

C

NO

NO

AL1

(Alarm Output 1)

AL2 / PO2

(Alarm Output 2 or

Process Output 2)

Process

Input

5A@250V

5A@250V

Seral Communcaton���

(RS485, Modbus RTU)

A+

B-

PID+

Eco

PT-100

TC

Supply

Swtch�

L

N

Supply

Voltage

1A T

Fuse

NOTE-1

AL1 / PO2

(Alarm Output 1 or

Process Output 2)

Process

Input

8

9

10

11

C

NO

5A@250V

12

13

14

PT-100

TC

The Devce �

wth Two Relays�

The Devce �

wth One Relay�

Çalma Ekranışı

*1

*5

*2

*4

*2,3

*2,3

*7*6

Produktspecifikationer