Honeywell TL8100A1008/U Bruksanvisning

Honeywell Termostat TL8100A1008/U

Läs nedan 📖 manual på svenska för Honeywell TL8100A1008/U (12 sidor) i kategorin Termostat. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

INSTALLATION INSTRUCTIONS

69-2017EFS-05

Energy Veried

TL8100

7 DAY PROGRAMMABLE HYDRONIC THERMOSTAT

GUIDELINES

TURN OFF POWER TO THE HEATING SYSTEM AT

THE MAIN POWER PANEL TO AVOID ELECTRICAL

SHOCK. INSTALLATION SHOULD BE CARRIED

OUT BY AN ELECTRICIAN.

• For a new installation, choose a location about 5 ft.

(1.5 m) above the floor.

• The thermostat must be installed on an inside wall.

• Avoid locations where there are air drafts (top of

staircase, air outlet), dead air spots (behind a

door), direct sunlight, or concealed chimneys or

stove pipes.

PROCEDURE

1. Loosen the captive screw securing the front

module to the rear module as shown in Fig. 1.

2. Lift the lower part of the front module to remove

it from the rear module.

3. Loosen the captive screw holding the terminal

cover and remove the cover.

4. Pass the wires through the opening to the right

of the terminals. See Fig. 2. Secure the rear

module to an electrical box or to the wall using

the supplied wall anchors and screws.

5. Connect the wires (see section “Thermostat Wir-

ing” on page 2). Use 12 AWG or smaller wire.

14 AWG is recommended for line voltage,

18 AWG is recommended for 24 VAC.

6. Install the terminal cover and tighten the screw.

7. Configure the thermostat using the switches

located on the back of the front module (see

section “Thermostat Configuration” on page 3).

8. Install the batteries (see section “Power-up” on

page 3).

9. Mount the front module onto the rear module

and tighten the screw.

Fig. 1. Installation steps.

Fig. 2. Routing wires to thermostat.

231

4 5

M29963

SUPPLY

LOAD

PROVIDED

WIRES

M29964

TL8100

69-2017EFS—05 2

THERMOSTAT WIRING

Fig. 3. Wiring diagram for a line voltage circulator.

Fig. 4. Wiring diagram for a line voltage electric

heater.

Fig. 5. Wiring diagram for a line voltage valve

(V4043 or similar).

Fig. 6. Wiring diagram for a line voltage 3-wire valve

(V4044 or equivalent); V8044 may be used with 24

VAC power.

Fig. 7. Wiring diagram for a 24 VAC 2-wire valve

(V8043A,E or equivalent).

Fig. 8. Wiring diagram for a 24 VAC V8043F.

Fig. 9. Wiring diagram for a White Rogers 1311

valve.

Fig. 10. Wiring diagram for a 24 VAC furnace or

hydronic zone panel.

Remote Input Wiring

The thermostat has an input for connecting a home

automation system or a remote control system. When

a signal is received at this input, the thermostat

switches to Vacation mode. When the signal is

removed, the thermostat returns to the original mode.

See Fig. 11.

Fig. 11. Wiring for a home automation system.

M29965

120 VAC OR 240 VAC

2 AMP MAXIMUM INDUCTIVE LOAD

TL8100

M29966

N120/240 VAC

5 AMP MAXIMUM RESISTIVE LOAD

L N

ELECTRIC HEATER

TL8100

M29967

120/240 VAC

2 AMP MAXIMUM INDUCTIVE LOAD

V4043

L N

TL8100

M29968

RED

BLUE

YELLOW

MOTOR

V4044 OR V8044

VALVE OPERATOR

TL8100

M29977

V8043A, E

CONNECT BLACK WIRES ON V8043A AND

YELLOW WIRES ON V8043E.

TL8100

M29978

V8043F

TH, TR TH TR

TL8100

254

6 1 3

1311

M29970

M29971

RFURNACE OR

T, T ON PANEL

TL8100

TL8100 HOME AUTOMATION

SYSTEM

12 VDC

± 10%

M29972

TL8100

3 69-2017EFS—05

THERMOSTAT

CONFIGURATION

Table 1 shows the configuration of the switches on the

back of the front module. Default settings are inside

the shaded cells.

Temperature Control Mode

Choose proportional adaptive mode by placing switch

#5 in the up position for these types of systems.

• Hot water heat systems

• Gas, oil, or electric furnaces

• Electric radiant or convection heating

See Table 2 to set switches #1 and #2 for how to

configure proportional adaptive mode.

Choose conventional mode by placing switch #5 in

the down position for these types of systems:

• Gas or oil furnace or boiler with a 30-second or

longer combustion gas prepurge cycle. To figure

out the gas purging cycle of your system, measure

the time lapse from the instant the thermostat

sends the heating command to the instant the

burner actually goes on.

• Systems where the user desires to set how many

degrees the air temperature must fall before the

thermostat calls for heat. In general, the slower the

HVAC system is able to distribute heat, the smaller

the the differential should be.

• When more than one TL8100 is wired directly to

one zone valve or one zone circulator.

See Table 3 to set switches #1 and #2 for how to

configure conventional mode.

POWER-UP

When you install the batteries, the unit

performs a series of tests for a few

seconds before displaying the ambient

temperature.

It is normal that the displayed

temperature be higher than the ambient

temperature if you are holding the

thermostat. Once installed on the wall,

the thermostat will display the true

ambient temperature after one hour.

Table 1.

Switches Description Up Down

1 & 2

Cycle length

(proportional)

Deadband

(conventional)

See Table 2 and 3.

3 Clock display 12H 24H

4Temperature

display a

aEvery time you change the temperature display for-

mat, the comfort and economy preset temperatures

return to their default settings.

°F °C

5Temperature

control mode

Proportional

Mode

(see

“Temperature

Control

Mode”)

Conventional

Mode

(see

“Temperature

Control

Mode”)

6Pump

protection b

bFor hot water installations, it is recommended to

enable this function to activate the pump for

one minute every 24 hours to prevent pump seizure.

Deactivate Activate

Table 2. Proportional Mode.

Cycle

length Heating Type Position

minutes

(12 CPH)

For faster cycling systems

minutes

(6 CPH)

Fossil fuel or electric wall furnaces,

electric forced air, electric radiant or

convection heating

minutes

(4 CPH)

Standard efficiency fossil fuel forced

air systems or high temperature, fast

response, hot water systems

minutes

(3 CPH)

High efficiency fossil fuel systems or

slow response hot water systems

Table 3. Conventional Mode.

Differential Position

0.5 °F (0.3 °C)

0.7 °F (0.4 °C)

0.9 °F (0.5 °C)

1.1 °F (0.6 °C)

Produktspecifikationer

Varumärke:	Honeywell
Kategori:	Termostat
Modell:	TL8100A1008/U
Enhetsplacering:	Ingebouwd
Typ av operation:	Draaiknop
Färg på produkten:	Roestvrijstaal
Inbyggd display:	Nee
Timer:	Nee
Bredd:	600 mm
Djup:	510 mm
Höjd:	40 mm
Typ av material (överst):	Roestvrijstaal
Antal brännare/kokzoner:	4 zone(s)
Typ av häll:	Gaskookplaat
Elektronisk tändning:	Ja
Sjud brännare/kokzon:	1000 W
Normal brännare/kokzon:	1750 W
Kontrollposition:	Voorkant
Installationsfackets bredd:	560 mm
Installationsfack djup:	480 mm
Installationsfack höjd:	40 mm
Stor brännare/kokzon:	1750 W
Pannstödsmaterial:	Gietijzer
Säkerhetsventil:	Ja
Extra stor höghastighetskokzon:	3800 W
Wokbrännare:	Ja
Wokbrännares läge:	Links
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 - 60 Hz