Hudson Valley Collins 2938-PN Bruksanvisning
Hudson Valley
Lampa
Collins 2938-PN
Läs gratis den bruksanvisning för Hudson Valley Collins 2938-PN (1 sidor) i kategorin Lampa. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 1.5 recensioner. Har du en fråga om Hudson Valley Collins 2938-PN eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
2914,2919,2924,2938
Hudson Valley Lighting, Inc.
P.O. Box 7459
106 Pierces Road
Newburgh, NY 12550
(800) 814- 3993
www.hudsonvalleylighting.com
GENERAL
1. To ensure the success of the fixture installation, the following instructions and
diagram(s) should be read and understood.
2. All electrical connections must be made in accordance with the National Electric
code and local codes and ordinances. If you are uncertain of the methods of
installing electrical wiring and lighting fixtures secure the services of a qualified
licensed electrician.
3. TOOLS NEEDED: Blade screwdriver, phillips screwdriver, slip joint pliers or
small adjustable wrench, wire cutter/stripper, electrical current tester, stepladder
and electrical tape. NOTE: The important safeguards and instructions outlined on
this sheet are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors that
cannot be built into any product. Caution and care must be supplied by the
person(s) installing, operating and maintaining this lighting fixture.
INSTALLATION PREPARATION
1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE LIGHTING
FIXTURE IS TO BE ATTACHED. Move the appropriate circuit breaker to the “off
position or completely remove the fuse controlling the circuit.
2. If an existing fixture is being replaced, remove it and note to which of the wires
in the outlet box the fixture was attached. DO NOT SEPARATE ANY OTHER
WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF
OLDER WIRING. In regular circumstances the BLACK wire will be the “Hot” lead
and the WHITE wire will be the “Neutral” or “Common” lead. A GREEN or BARE
COPPER wire is the “Ground”. In older buildings it is always good practice to
reconfirm the polarity of the wiring.
3. This fixture is designed to be mounted on a standard round or octagon box. The
box must be securely mounted to the structure of the building.
FIXTURE INSTALLATION
1.Remove the fixture and parts bag(s) from the carton. Before discarding the carton,
double check packing to make certain that all parts are found.
2. Remove the 2 nuts holding the mounting to the fixture.End plate
(Starting at the back), thread the 2 longest mounting screws into the mounting plate
(The green screw is in the front). Attach the mounting plate to the outlet box. (The
green screw should face the floor).
3.Thread the small hex nuts onto the mounting screws. Lock the hex nuts against the
mounting plate.
4.Thread lead ground wire through pipe stem and twist tightly onto body. Keep adding
additional stems required.
5. Thread wire through canopy and carefully slide over stem.
6. Install ball swivel on end of stem.
7.Trim excess wire to min. 6” beyond stem, strip to 5/8” and twist.
8. e canopy up and be sure to align tab with groove in ball swivel.Slid
9 . Fasten the bare copper fixture wire to the green or bare copper wire in the box
or bare copper wire in the box to the crossbar with green screw provided.
NEVER FASTEN THE GROUND WIRE TO THE BLACK OR “HOT” WIRE!
FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN SERIOUS
INJURY OR DEATH!
10. Fasten the white fixture wire to the white wire in the outlet box. Fasten the wires
to together with an approved fastener(wire nut). Starting about 1” b elow the fastener,
tightly wrap connection with the electrical tape so that the tape seals the end of the
fastener. Make sure that there is no exposed wire or strands that could cause a
dangerous short circuit!
11 ack wire in the outlet box. Fasten the. Connect the black fixture wires to the bl
joined wires as in step 10.
12 . Position and mount canopy to outlet box at ceiling with end nuts.
13. Place the shade on the frame.
14 . C. . Install the lamp ( light bulb) NOTE: This fixture is rated for 60 watt type
DO NOT EXCEED RECOMMENDED WATTAGE !
15. Restore power to circuit at breaker or fuse box.
Produktspecifikationer
| Varumärke: | Hudson Valley |
| Kategori: | Lampa |
| Modell: | Collins 2938-PN |
Behöver du hjälp?
Om du behöver hjälp med Hudson Valley Collins 2938-PN ställ en fråga nedan och andra användare kommer att svara dig
Lampa Hudson Valley Manualer
29 Juni 2025
29 Juni 2025
28 Juni 2025
28 Juni 2025
28 Juni 2025
28 Juni 2025
Lampa Manualer
- Hatco
- Werma
- X4-Tech
- InFocus
- Frandsen
- Mio
- Adj
- Yeelight
- Thermaltake
- Maul
- Jinbei
- Falcon Eyes
- Zhiyun
- Neo
- Ledlenser
Nyaste Lampa Manualer
29 Juni 2025
29 Juni 2025
29 Juni 2025
28 Juni 2025
27 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025