IPEGA PG-P5016 Bruksanvisning


Läs gratis den bruksanvisning för IPEGA PG-P5016 (1 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 1.5 recensioner. Har du en fråga om IPEGA PG-P5016 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/1
1. 外接5V 其它电源可能会导致本产品工作异常。
2. 产品注意事项:
使用本产品时必使用P5原装主机提供电源。
当P5手柄充电电量达到约80%以上电如果时候去拔掉手柄再插入
充电会因手柄有电池保护功能手柄可能会不充电等手柄电池电低于80%
以下电才会继续充电。
3.本产品在期不使用时应将电源USB插头从P5主机上取出。
4.本产品在使用或存放时应尽量避开灰尘、以免影响使用寿命。
6.本产品因使用不当而成浸水、撞坏或摔坏出现电气性能问题停止使用。
7.如有损坏及时维修部门处理切勿自行拆卸。
双充 x1
1.将P5016彩虹桥双充底的可凝胶撕掉。 2.将P5016彩虹桥双充从①点按压下去然后按
依次嵌入主里面,带线4P公头接入原装P5主机后
USB母座此时LOGO亮白灯其它亮蓝灯
4.P5016彩虹桥双充也可以放到桌上充电。3.分别将两个P5手柄的四个探接触对准P5016
座充上各自的四个再插入手柄此时对应的红灯
开始充充满亮蓝灯 。
产品说明书PG-P5016)
P 5
工作电压DC 5V 充电时间:2.5-3H左右 充电电流 ≤850 mA(单个手柄
1.本产品用于给P5原装手柄充电。
2.带充电指示灯在充电程中便于识别充电状态。
3.备专用的两个充电探手柄充电时放使用常方便。
4.产品内有内置直流升压稳压电能持续提供5V稳压充电。
产品特征
注意事项:
产品使用说明
1. External 5V, other power supply may cause this product to work abnormally.
2. Product note:
①: P5 original console must be used to provide power when using this product.
②: When the charging power of the P5 gamepad reaches up to 80% or more, if you
remove the gamepad and plug it again at this time, the gamepad may not be charged
due to the battery protection function of the gamepad; you need to wait until the battery
power of the gamepad is lower than 80%.
3. When this product is fully charged or not in use, the power USB plug should be
removed from the P5 console.
4. When this product is used or stored, dust and heavy pressure should be avoided as
much as possible, so as not to aect the lifetime.
5. This product is immersed in water, crashed or broken due to improper use, and
electrical performance problems occur. Please stop using it.
6. This product cannot be used or stored in a humid environment.
7. If there is any damage, please send it to the maintenance department for disposal,
and do not disassemble it by yourself.
3. Align the four probes of the two P5 gamepad with the four probes on the P5016
socket, and then insert the gamepad. At this time, the corresponding red light will
be on to start charging, and when fully charged, the light will be blue.
4. When the P5016 Rainbow Bridge Dual Charger is can be charged on the desktop
Manual(PG-P5016)
P5 Rainbow Bridge Dual Charger
Working voltage: DC 5V Charging time: 2.5-3H
charging current: ≤850 mA (single gamepad)
1. Tear o the gel at the bottom of the P5016 Rainbow Bridge Dual Charger
2. Press down the P5016 Rainbow Bridge Dual Charger from point ①, and then follow the sequence
Embed in the console one by one, with the cable 4P male connector connected to the back of the original
P5 console USB female socket; at this time, the LOGO lights up in white, and the other lights in blue.
1. This product is suitable for charging P5 original gamepad.
2. With charging indicator, it is easy to identify the charging status during the charging process.
3. Equipped with two dedicated charging probe positions, it is very convenient to take it away or
put it down for charging.
4. The product has a built-in DC boost regulator circuit, which can continuously provide 5V
regulated charging.
Applicable instructions:
Equipment instructions:
Illustration
Electrical parameters:
Product Note:
80g书写纸 单色双面印刷 315*142MM
Patent NO. : ZL202130111339.X
ZL202130111339.X
Dual Charger x1
充电指示灯
充电卡槽 1
充电卡槽 2
USB 头
1
Manual X1
Product note:
Charging tank 1
Charging tank 2
Charging indicator
panel
USB port
可凝胶
2
1
Remove gelable
2
3 4
3 4


Produktspecifikationer

Varumärke: IPEGA
Kategori: ej kategoriserat
Modell: PG-P5016

Behöver du hjälp?

Om du behöver hjälp med IPEGA PG-P5016 ställ en fråga nedan och andra användare kommer att svara dig