IPEGA PG-QT03A Bruksanvisning
IPEGA
ej kategoriserat
PG-QT03A
Läs gratis den bruksanvisning för IPEGA PG-QT03A (1 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 2.5 recensioner. Har du en fråga om IPEGA PG-QT03A eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
1. Input: DC 5V/2A
2. Output: DC 5V/2A
3. Charging Time: 3 hours
4. Battery Capacity: 20000 mWh
5. Battery Life for Quest 2:
Approximately 120 minutes
6. Battery Life for Quest 3:
Approximately 90 minutes
Output
connector
On/Off
Type-C
charging port
Power
indicator light
1. This product is suitable for Quest 2/3.
2. It has 4 blue LED indicators to display
the battery level in real to time.
4. Do not use chemical solvents to clean
this product.
5. Please do not store this product in
damp or high-temperature areas.
6. Avoid hitting, dropping, piercing, or
attempting to disassemble the product
to prevent unnecessary damage.
7. The product contains electronic
components such as batteries and
capacitors and should not be disposed
of casually. Please dispose of them
properly by giving them to qualified
recycling facilities.
8. If certain products cannot connect or
operate due to uncontrollable factors,
our company does not assume any
responsibility. We reserve the right to
provide the final interpretation in such
cases.
- The battery level of the pack will be
displayed as a percentage (e.g., if three
LEDs are solidly lit, the battery level is
at 75%).
- As charging continues, the battery
pack's remaining charge will gradually
decrease until the battery is depleted
and requires recharging.
- After the LED lights turn off, short
press the power button once to display
the current battery level and activate
the output.
3. Double press the power button to turn
off the LED lights and stop the output.
4. The battery pack includes overcurrent,
short circuit, and temperature protection.
The battery cells comply with standard
battery certifications.
1. Charging the Battery Pack:
- Connect one end of the Type-C
charging cable to the original adapter,
and the other end to the Type-C input
port of the battery pack.
- Plug in the adapter to begin charging
the battery pack.
- All four LED lights will cycle once,
then a single LED will blink to indicate
that charging is in progress. The battery
level is shown as a percentage (e.g., if
two LEDs are solidly lit, the battery level
is at 50%). When fully charged, all LEDs
will be lit, indicating 100%.
- After unplugging the charging cable,
the LEDs will turn off after approximately
38 seconds.
2. Charging the Quest 2 (or Quest 3) VR
Headset:
- Insert the Type-C output cable from
the battery pack into the Quest 2 (or
Quest 3) VR headset’s input port.
- The battery pack will automatically
detect and begin charging the VR
headset.
1. If the battery pack is not used for an
extended period, it should be charged
every three months.
2. If the battery pack remains unused and
uncharged for more than six months, it
may experience deep self-discharge,
making it impossible to recharge.
3. Do not disassemble or short-circuit the
output end of the battery pack for
extended periods, as this may cause
irreversible permanent damage.
Battery pack x 1 Manual x 1
Type-C cable x 1
VR Power Battery Pack
User Manual (PG-QT03A)
Specifications: (10W)
Function Keys：
Product Description：
Product instructions:
Note:
Product List:
1. 输入：DC 5V/2A
2. 输出：DC 5V/2A
3. 充电时间：3H
4. 电池容量：20000mWh
5. 续航Quest 2：约120分钟
6. 续航Quest 3：约90分钟
输出接头
电源开关
充电接口
电量指示灯
1. 本产品适用于Quest2(Quest3)VR眼镜
充电。
2. 具备4个蓝色LED实时显示电池电量。
3. 装配方便，操作简单。
1. 不使用期间，每三个月需给电池包充电
补充电能；
2. 超过六个月未使用，也未给电池包进行
充电有可能造成电池深度自放电而无法
充电进行使用；
3. 不可拆解或短路电池包输出端，以免造
成不可逆永久损坏。
4. 请勿采用化学溶剂清洗本产品。
5. 请不要把本产品在潮湿或高温地方存储。
6. 不要敲击、摔打、刺穿、或试图去分解
本产品，以免对产品造成不必要的损害。
7. 产品内有电芯和电容等电子材料，不可
随便丢弃，须集中给有资质的回收机构。
8. 因不可抗拒的因素造成部分产品无法连
接操作，我公司不负任何责任，对此我
公司保留最终解释权；
3. 短按2次开关为关闭LED和输出。
4. 电池包具有过流和短路及温度保护，
电芯要符合常规电池认证。
操作说明:
1. 连接TYPE-C充电线一端到原装适配器，
另一端到电池包输入TYPE-C母座，接
通电源给电池包充电，4颗LED灯循环
跑马点亮1次后，单颗LED灯闪烁表示
正在充电，电池包电量百分比（如2个
灯常亮为当前电量为50%），充满为
100%。拔掉充电线后约38秒灯熄灭；
2. 电池包给Quest2(Quest3)VR眼镜充电，
将电池包输出线TYPE_C公头插入
Quest2(Quest3)VR眼镜母座，自动识
别充电。电池包电量百分比（如3颗灯
常亮表示当前充电包电量为75%），
随着充电时间的增加，电池包电量显
示将逐渐递减。直至电池包电量放完
后需重新给电池包充电。LED灯熄灭
后短按1次开关显示当前电量，同时打
开输出。
电池包 x 1 说明书 x 1
充电线 x 1
Quest VR眼镜电池包
产品说明书(PG-QT03A)
(10W)
Produktspecifikationer
| Varumärke: | IPEGA |
| Kategori: | ej kategoriserat |
| Modell: | PG-QT03A |
Behöver du hjälp?
Om du behöver hjälp med IPEGA PG-QT03A ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat IPEGA Manualer
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
ej kategoriserat Manualer
- Tach-It
- AeroCool
- Marshall Electronics
- Timbersled
- Tesla
- Livington
- CFH
- Jenn-Air
- American Standard
- AV:link
- Defender
- Ikan
- MB Quart
- White Lightning
- Thermaco
Nyaste ej kategoriserat Manualer
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025