IPEGA PG-QT04B Bruksanvisning


Läs gratis den bruksanvisning för IPEGA PG-QT04B (1 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 2 recensioner. Har du en fråga om IPEGA PG-QT04B eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/1
Quest VR眼镜充电底座
产品说明书(PG-QT04B)
产品使用
1. 将适配器充电线的TYPE- C公头插入本产品的TYPE- C母座
3. LED充电指示灯1.待机绿色常亮充电时常亮红色、2.充满电后常亮绿色
4. VR头戴充电时,随着VR头戴的电池电量逐步上升充电电流会步下降,
直到充满电指示灯转绿色灯。
5. 按一下产品前灯光摸按键,可以切换RGB灯光效果,按灯光摸按
3秒保存当前灯光模式并熄灯。
注意:
如不能充电请检查磁吸头与充电线有无接触到位
2. 将本产品配置的电池入VR手柄然后上本产品配置的充电电池盖将安
完成后的VR手柄对应的接点与本产品充电底座对应的充电探
放好即可为手柄进行充电对应的左右指示灯红色表示左右手柄充电状态。
左右指示灯显示红色,表示左右手柄充电状态
将本产品带的磁吸头
TYPE-C公头插入VR头戴
将磁吸头的TYPE -C与本机的磁吸头线相吸
即可进行充电对应的中指示灯显示红色
指示灯显示红色,表示VR眼充电状态
1. 本产品用于Quest 3s/Quest 3/Quest 2 VR眼及手柄充电。
2. 本产品具备1个TYPE-C 2.0入口和1个USB2.0出口。
3. 具备1个VR头戴充电出口最大充电电流5V/3A(或9V/2A)左右。
4. 具备2个VR手柄充电出口。
5. 具有炫彩灯效并可以摸切换。
注意由于控制器电池装,VR头戴上显示的控制器电池电不准确。
以充电座上的控制器指示灯为准。
注意本产品带有充电保护(额定30W),触发保护则产品反复拔下
背面usb接的备即可。
注意事项:
产品清单
2. 敲击、摔打、刺穿、或图去分本产品以免对产品成不必
的损害。
3. 专业人员勿拆卸本产品,否则不在售后保修服务内。
4. 产品内有电容电子材料不可便丢弃,须集资质的回收机构。
5. 因不可抗拒的因素造分产品无法接操作我公司不任何
此我公司保留最终解释权。
充电底座 x1
电源线 x1 明书 x1
磁吸接头 x2 电池 x2 电池盖 x4
1. 入电压/电流DC 9-20V/2.0A
2. 手柄充电电流600mA
3. 充电电池1.2V/1800mA
VR左手柄充电
灯光摸按
USB出接口
电源入接口
VR右手柄充电接
VR眼充电头
磁吸接头收
注意:如手柄无法充电,请
检查电池是否正确安装,确
保电池盖上的触点与电池侧
面的金属面正常接触
充电指示灯
Quest VR Headset Charging Stand
Product Manual(PG-QT04B)
5. Press the light touch button on the front of the product to switch the RGB
lighting effect. Press and hold the light touch button for 3 seconds to save
the current lighting mode and turn off the light.
6. USB A expansion port, can be used to charge other devices.
3. Led charging indicator: 1. Standby green color always on, charging turn to
red. 2. Change to green color while full charged.
4. When charging the VR headset, with the VR headset battery power gradually
increases, the charging current will gradually decrease until the light color
turn. Light indicator turn to green color while full charged.
2. Install the battery configured with this product into the VR controller, then
install the rechargeable battery cover, place the contact point corresponding
to the installed VR controller, in contact with the charging probe position
corresponding to the charging base of this product to charge the controller.
The corresponding left and right indicator turn red to indicate the charging
status of the left and right controllers.
The left and right indicator lights are red,
indicating the left and right controllers in
charging status.
Applicable Instructions
Product Appearance Illustration:
Electrical Parameters:
1. This product is suitable for Quest 3s/Quest3/Quest 2 VR headset and
controller charging.
2. With 1 TYPE-C 2.0 input and 1 USB 2.0 output port.
3. Equipped with 1 VR headset charging output port, max charging current is
5V/3A(or 9V/2A).
4. Equipped with 2 VR controller charging output ports.
5. With colorful lighting effects and can be switched by touch.
Note: since the controller battery is not original, the controller battery level
displayed on the VR headset is inaccurate. Please refer to the controller
indicator light on the charging dock.
Note: This product with charging protection(rated power 30W). If the protection
is triggered, the product will restart repeatedly. Just unplug the device
connected to the USB on the back.
Notes
Product List
1. Please do not put the products in wet or high temperature place.
2. Don’t knock, beat, drub, pierce, or try to decompose this product, avoid
any unnecessary damage to the product.
3. Non-professionals disassemble this product by mistake otherwise it will not
be cover by the after-sales warranty service.
4. The product contains capacitors and other electronic materials, which
cannot be discarded casually, should be collected by qualified recycling
agencies.
5. If some products can not be connected due to irresistible factors, our
company will not be responsible for any consequences. Our company
reserves the final right interpretation.
6. Do not use it to charge other types of rechargeable batteries or controllers.
Charging Station x 1
Type-C Cable x 1 Manual x 1
Magnetic Interface x 2 Battery x 2 Battery Cover x 4
1. Input voltage/current: DC 9-20V/2.0A
2. controller charging current: 600mA
3. Charging battery: 1.2V/1800mA
VR left controller
charging contact
point
Light touch button
USB output port
Power input port
VR right controller
charging contact point
VR headset
charging head
Magnetic connector
storage slot
Note: If the controller
cannot be charged,
please check whether the
battery is installed
correctly, and ensure that
the contacts point on the
battery cover are in
normal contact with the
metal surface on the side
of battery.
Charging
indicator
Product Instructions
1. Insert the TYPE-C male end of the adapter charging cable into the TYPE-C
female input end of this product.
Note:
If not charging please check whether the
magnetic charging connector and the
charging cable are in proper contact.
Insert the attached
magnetic TYPE-C male
connector included with
the product into the VR
headset.
Attach the TYPE-C port of the magnetic
connector to the magnetic head cable of the
device to charge, and the corresponding middle
indicator light turn red.
Middle indicator light turn red, it shows VR
headset in charging status.


Produktspecifikationer

Varumärke: IPEGA
Kategori: ej kategoriserat
Modell: PG-QT04B

Behöver du hjälp?

Om du behöver hjälp med IPEGA PG-QT04B ställ en fråga nedan och andra användare kommer att svara dig