Microchip HV9910BDB1 Bruksanvisning
Microchip
Inte kategoriserad
HV9910BDB1
Läs gratis den bruksanvisning för Microchip HV9910BDB1 (12 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 5 recensioner. Har du en fråga om Microchip HV9910BDB1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/12
Supertex inc.
Supertex inc.
www.supertex.com
Doc.# DSDB-HV9910BDB3
A032813
HV9910BDB3
General Description
The HV9910BDB3 demoboard is a high current LED driver
designed to drive one LED or two LEDs in series at currents
up to 1.0A from a 10 – 30VDC input. The demoboard uses
Supertex’s HV9910B Universal LED driver IC to drive a
buck converter.
The HV9910BDB3 can be congured to operate in either a
constant frequency mode (for driving a single LED) or in a
constant o-time mode (for driving two LEDs).
The output current can be adjusted in two ways – either
with linear dimming using the onboard potentiometer or
with PWM dimming by applying a TTL – compatible square
wave signal at the PWMD terminal. Using linear dimming,
the output current of the HV9910DB1 can be lowered to
about 0.01A (note: zero output current can be obtained
only by PWM dimming).
Connection Diagram
Low Voltage, High Current,
LED Driver Demoboard
Specications
Parameter Value
Input voltage 10 - 30VDC
Output voltage -
constant frequency mode 2.0 - 4.5V
Output voltage -
constant o-time mode 4.0 - 8.0V
Maximum output current 1.0A ± 10%
Output current ripple (typ) 20% (peak-peak)
Efciency (@ 12V input) 86% (for one LED)
93% (for two LEDs)
Open LED protection yes
Output short circuit protection no
Dimensions 48.2mm X 29.0mm
Connections
1. Input Connection - Connect the input DC voltage
between VIN and GND terminals of connector J1 as shown
in the connection diagram.
2. Output Connection - Connect the LEDs between
LED+ (anode of LED string) and LED- (cathode of LED
string) of connector J2.
a. If the load is one LED, short the RT and FREQ
terminals of connector J4 using a jumper.
b. If the load is two LEDs, short the RT and OFFT
terminals of connector J4 using a jumper.
3. PWM Dimming Connection
a. If no PWM dimming is required, short PWMD and
VDD terminals of connector J3.
b. If PWM dimming is required, connect the TTL-
compatible PWM sourc between PWMD and GND
terminals of connector J3. The recommended PWM
dimming frequency is ≤ 1.0kHz.
+
Short for constant
frequency mode
+
-
Short for
constant o-time mode
Produktspecifikationer
| Varumärke: | Microchip |
| Kategori: | Inte kategoriserad |
| Modell: | HV9910BDB1 |
Behöver du hjälp?
Om du behöver hjälp med Microchip HV9910BDB1 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Microchip Manualer
12 Mars 2025
12 Mars 2025
6 Mars 2025
5 Mars 2025
4 Mars 2025
4 Mars 2025
2 Mars 2025
2 Mars 2025
2 Mars 2025
2 Mars 2025
Inte kategoriserad Manualer
- Aqua-Vu
- Huntleigh
- Lazer
- Insteon
- Adidas
- PureLink
- Vivotek
- Lapp
- Elinchrom
- GPO
- True & Tidy
- IOptron
- Drawmer
- Xavax
- Osram
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025