Muller SC 95.47 pro Bruksanvisning

Läs gratis den bruksanvisning för Muller SC 95.47 pro (4 sidor) i kategorin Hemautomation. Guiden har ansetts hjälpsam av 22 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 3 recensioner. Har du en fråga om Muller SC 95.47 pro eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

www.hugo-mueller.de BA HUpro GB -22989- 2014-07-V03 - ED - A3 Seite 1

GB

Additional instruction masterclockSite 1 / 2

PLEASE NOTE!!!

SAFETY INSTRUCTIONS

(SC 58.17 pro / SC 98.47 pro / SC 53.17 pro / SC 93.47 pro)

Please note the following for masterclock with time switch functionality:

This manual describes only masterclock features. Time switch relevant description can be

found in the standard time switch manual!

Only the connection diagram, initial operations and the safety instructions of this manual is

valid.

!!ATTENTION!!DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!!

=> Installation and assembly of electrical equipment must be carried out only by a skilled person!!!

=> Disconnect device from power supply for wiring and installation purposes!!!

=> Defective devices have to be put out of service immediately!!!

Connect the supply voltage/frequency as stated on the product!

Warranty void if housing opened by unauthorised person!

The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if

external influences exceed certain limits!

Installation and assembly of electrical equipment must be in accordance with local building and electrical

codes!

The disposal of the device (and batteries) must be in accordance with the valid environmental and national law!

SC 58.07 pro (DIN rail mounting – master clock)

Technical dataslave-clock-line (SL)

Initial operation

SC 58.07 pro

Connection diagram

Number of lines: 1

Output voltage: 24VDC

Output current: 35mA

Conn. terminals: 17 / 18

Max. number clocks: approx. 5 slaveclocks

Output signal: Pole changing pulse

Pulse sequence:Normal operation= 1/min

During adjustment = 10/min

Pulse length: 2 sec.

(Pulse sequence/lengthadjustable)



The time switch is delivered in power back up mode (battery mode).

The display shows the power plug symbol [flashing ].



Press -button for 1 second.The display switches to automatic-mode.

(Displaying the time and the current status of the slave-clock-line (SL)).

The masterclock is already programmed with the current date and time and European

daylight savings time is activated.The slave-clock-lineis preset as follows: Minute-line

activated/ start time 12:00 / Slave-clock-line (SL)is stopped.

Power supply masterclock (See connection diagram on the left)



Connect the supply voltage/frequency as stated on the product!

Connection slave-clock-line (SL)=> master clock (See

connection diagram on the left)



Connect slave-clock-line to terminal no. 17 and 18 of the master clock.

SC 58.08 pro (DIN rail mounting – master clock)

Technical data slave-clock-line (SL)

Initial operation

SC 58.08 pro

Connection diagram

Connection sample

Number of lines: 1

Output voltage: Max. 250V~ (potential-free)

Output current: 1A

Conn. terminals: 2 / 8

Max. number clocks: Depends on the slaveclocks

Pulse sequence: Normal operation = 1/min

During adjustment = ca. 6/min

Pulse length: 8 sec.

(Pulse sequence/length adjustable)

PLEASE NOTE: The two relays are

energized alternately every minute.



The time switch is delivered inpower back up mode (battery mode).

The display shows the power plug symbol [flashing ].



Press -button for 1 second. The display switches to automatic-mode

(Displaying the time and the current status of the slave-clock-line (SL)).

The masterclock is already programmed with the current date and time and European

daylight savings time is activated. The slave-clock-line is preset as follows: Minute-line

activated / start time 12:00 / Slave-clock-line (SL)is stopped.

Power supply masterclock (See connection diagram on the left)



Connect the supply voltage/frequency as stated on the product!

Connection slave-clock-line (SL)=> master clock (See

connection diagram on the left)



Connect slave-clock-line to terminal no. 2 and 8 of the master clock.

Power supply slave-clock-line (SL) (See connection diagram on the left)



Connect power supply for clock motor(s) to terminals 1 / 9 and 3 / 7

SC 58.17 pro (DIN rail mounting – master clock with time switch functianality / weekly time switch)

Technical data slave-clock-line (SL)

Initial operation

SC 58.17 pro

Connection diagram

Number of lines: 1

Output voltage: 24VDC

Output current: 150mA

Conn. terminals: 17 / 18

Max. number clocks: approx.20 slaveclocks

Output signal: Pole changing pulse

Pulse sequence:Normal operation = 1/min

During adjustment= 10/min

Pulse length: 2 sec.

(Pulse sequence/length adjustable)



The time switch is delivered in power back up mode (battery mode).

The display shows the power plug symbol [flashing ].



Press -button for1 second. The display switches to automatic-mode

(Displaying the time and the current status of the slave-clock-line (SL)).

The master clockis already programmed with the current date and time and European

daylight savings time is activated. The slave-clock-line is preset as follows: Minute-line

activated / start time 12:00 / Slave-clock-line (SL) is stopped.

Power supply master clock (See connection diagram on the left)



Connect the supply voltage/frequency as stated on the product!

Connection slave-clock-line (SL)=> master clock (See

connection diagram on the left)



Connect slave-clock-line to terminal no. 17 and 18 of the master clock.

SC 98.47 pro(DIN rail mounting – master clockwith time switch functianality / yearly time switch)

Technical data slave-clock-line (SL)

Initial operation

SC 98.47 pro

Connection diagram

Number of lines: 1

Output voltage: 24VDC

Output current: 300mA

Conn. terminals: 35 / 36

Max. number clocks: approx. 40 slaveclocks

Output signal: Pole changing pulse

Pulse sequence:Normal operation = 1/min

During adjustment = 10/min

Pulse length: 2 sec.

(Pulse sequence/length adjustable)



The time switch is delivered in power back up mode (battery mode).

The display shows the power plug symbol [flashing ].



Press -button for 1 second. The display switches to automatic-mode

(Displaying the time and the current status of the slave-clock-line (SL)).

The master clockis already programmed with the current date and time and European

daylight savings time is activated. Theslave-clock-line is preset as follows: Minute-line

activated / start time 12:00 / Slave-clock-line (SL)is stopped.

Power supply master clock (See connection diagram on the left)



Connect the supply voltage/frequency as stated on the product!

(Master clock = terminals 22/23 / Time switch = terminals4/5).

Connection slave-clock-line (SL)=> master clock (See

connection diagram on the left)



Connect the slave-clock-line (SL)to the master clockon terminals 35 and 36

SC 53.17 pro (19”-housing –master clockwith time switch functianality / weekly time switch)

Technical data slave-clock-line (SL)

Initial operation

SC 53.17 pro

Connection diagram

SC 53.17: 2 NU-Linie

The signal output for line 1 and line 2 can be configured

independently to emit pulseseither every second or every minute!

NOTE! Power supply from a third party supplier:

The usage of a switched-mode power supply to drive the slave clock line

might disturb the reception of the FU 20.00 pro radio receiver. If the radio

receiver has no reception (the green LED on the bottom of the radio

receiver flashes rapidly or not at all)please connect GND of your

switched-mode power supply via an Y-capacitor with protective earth.

Number of lines: 2

Input USL: 24VDC (12VDC/48VDC/60VDC)

(Monitoring USL - switchable)

Output current: up to1500mA for each line

(Depends on the power supply)

Conn. terminals: See conn. diagram on the left

Max. number clocks: approx. 200 slaveclocks

(each line)

Output signal: Pole changing pulse

Pulse sequence:Normal operation = 1/min

During adjustment = 10/min

Pulse length: 2 sec.

(Pulse sequence/length adjustable)

Module: NT 73 (Power adapter slave line)

Not included indelivery!



The time switch is delivered in power back up mode (battery mode).

The display shows the power plug symbol [flashing ].



Press -button for 1 second. The display switches to automatic-mode

(Displaying the time and the current status of the slave-clock-line (SL)).

The master clockis already programmed with the current date and time and European

daylight savings time is activated. The slave-clock-line is preset as follows: Minute-line

activated / start time 12:00 / Slave-clock-line (SL) is stopped.

Power supply master clock (See connection diagram on the left)



Connect the supply voltage/frequency as stated on the product! (Terminals32a und 32c).

Connection power supply the slave-clock-line (SL)=> master clock

(See connection diagram on the left)



Depending on the specifications of the slave clocks, connect 12VDC; 24VDC; 48VDC; or

60VDC to terminals 26a and 26c.

Check polarity.



For voltages of slave clocks which differ from 24VDC, the dip switches on the PCB have to

be configured as stated within the table on the left.

Connection slave-clock-line (SL)=> master clock (See

connection diagram on the left)



Connect slave-clock-line to:

Line 1 [L1] => terminals 24a und 24c

Line 2 [L2] => terminals 22a und 22c

Table dip switches

(Power supply monitoring of the slave-clock-

line)

SL S1 S2

SL S1 S2

12VDCON ON

48VDCOFF ON

24VDCON OFF

60VDCOFF OFF

SC 93.47 pro (19”-housing –master clockwith time switch functianality / yearly time switch)

Technical data slave-clock-line (SL)

Initial operation

SC 93.47 pro

Connection diagram

NOTE! Power supply from a third party supplier:

The usage of a switched-mode power supply to drive the slave clock line

might disturb the reception of the FU 20.00 pro radio receiver. If the radio

receiver has no reception (the green LED on the bottom of the radio

receiver flashes rapidly or not at all)please connect GND of your

switched-mode power supply via an Y-capacitor with protective earth.

Number of lines: 1

Input USL: 24VDC (12VDC/48VDC/60VDC)

(Monitoring USL -switchable)

Output current:up to 1500mA

(Depends on the power supply)

Conn. terminals: See conn. diagram on the left

Max. number clocks: approx. 200 slaveclocks

Output signal: Pole changing pulse

Pulse sequence:Normal operation = 1/min

During adjustment = 10/min

Pulse length: 2 sec.

(Pulse sequence/length adjustable)

Module: NT 73 (Power adapter slave line)

Not included indelivery!



The time switch is delivered in power back up mode (battery mode).

The display shows the power plug symbol [flashing ].



Press -button for 1 second. The display switches to automatic-mode

(Displaying the time and the current status of the slave-clock-line (SL)).

The master clockis already programmed with the current date and time and European

daylight savings time is activated. The slave-clock-line is preset as follows: Minute-line

activated / start time 12:00 / Slave-clock-line (SL) is stopped.

Power supply the master clock(See connection diagram on the left)



Connect the supply voltage/frequency as stated on the product! (Terminals32a und 32c)

Connection power supply slave clockline => master clock

(See connection diagram on the left)



Depending on the specifications of the slave clocks, connect 12VDC; 24VDC; 48VDC; or

60VDC to terminals 26a and 26c.

Check polarity.



For voltages of slave clocks w

hich differ from 24VDC, the dip switches on the PCB have to

be configuredas stated within the table on the left.

Connection slave-clock-line (SL)=> master clock (See

connection diagram on the left)



Connect slave-clock-line to terminal no. 24a and 24c of the master clock.

Table dip switches

(Power supply monitoring of the slave-clock-

line)

SL S1 S2

SC S1 S2

12VDCON ON

48VDCOFF ON

24VDCON OFF

60VDCOFF OFF

Produktspecifikationer