Noctua NH-D14 Bruksanvisning

Noctua kylsystem för dator NH-D14

Läs gratis den bruksanvisning för Noctua NH-D14 (4 sidor) i kategorin kylsystem för dator. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 2 recensioner. Har du en fråga om Noctua NH-D14 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/4

NH-D14

Installation Manual INTEL

Removing the mainboard

Step 1:

In case you want to use the cooler on an assembled system,

you first have to remove the mainboard from the case in order

to be able to install the supplied backplate.

Caution -: On LGA1366 and LGA1156/1155, the supplied back

plate will install over the mainboard’s stock backplate, so the

mainboard’s stock backplate must not be taken off.

Required mounting parts:

First put the four bolts into the holes appropriate for your

mainboard’s CPU socket.

Setting up the backplate

Step 2:

Thank you very much for choosing a Noctua cooler. This

manual will guide you through the installation process of

the SecuFirm2

mounting system step by step.

Prior to installing the cooler, please consult the compat-

ibility list on our website and verify that the cooler is fully

compatible with your motherboard. Should you encounter

any difficulties, please check the FAQs on our website and

don’t hesitate to contact our support team at support@

noctua.at.

Noctua cannot be held responsible for any damage or losses

caused by compatibility issues.

Multilingual versions of this manual are available on our

website: www.noctua.at

Caution: Please verify that all four bolts are put into the

appropriate holes fully pushed in.

Step 4:

Installing the mounting bars

First put the plastic spacers onto the bolts, then add the

mounting bars.

Noctua NH-D14 INTEL

Installation Manual

4x plastic spacers 4x thumbscrews

1x 3-in-1 Intel backplate

4x bolts for backplate 2x mounting bars

LGA1366 (80mm)

LGA1156/1155 (75mm)

LGA775 (72mm)

For use on LGA1366 and LGA1156/1155 mainboards, please

remove the rubber inlay. Make sure that the rubber inlay is

in place for LGA775.

LGA1366 & LGA1156/1155 LGA775

Caution: On LGA1156/1155, please make sure that the two

cuts in the supplied backplate align with the screws of the

mainboard’s stock backplate.

Caution: Choose the alignment of the mounting bars according

to the desired final orientation of the cooler:

Step 3:

Attaching the backplate

Place the backplate on the rear side of the mainboard so that

the bolts stick through the mounting holes.

1x LGA775 rubber inlay

Caution: Tighten the screws until they stop.

Caution: Make sure to use the correct holes on the mounting bars.

Fix the mounting bars using the 4 thumb screws.

Step 5:

Applying thermal paste

If there are residual traces of thermal paste or thermal pads

on your CPU, please clean them off first. Then press a small

drop (4-5mm diameter) of NT-H1 onto the centre of the heat-

spreader.

Caution: Applying too much thermal paste will lower the heat

conductivity and cooling performance!

Step 6:

Fastening the heatsink to the CPU

Caution: Please take off the protection cover at the bottom side

of the heatsink first!

Take off the centre fan. Then put the heatsink onto the CPU and

screw it to the screw threads of the mounting bars.

Caution: Tighten the screws until they stop.

Caution: Make sure that the curved sides of the mounting bars

are pointing outwards.

Connect the fan(s) to the mainboard, power supply or fan

controller. Use the supplied y-split cable to connect both fans

to one fan header.

Depending on your CPU and the temperature inside the case,

you may interconnect the supplied Ultra-Low-Noise Adapters

(U.L.N.A.) in order to further reduce the fans operating noise.

Use the black adaptor for the NF-P14 140mm fan and the

blue adaptor for the NF-P12 120mm fan.

Caution: Never use one adaptor for both fans by putting it

before the y-split cable.

Caution: When using the U.L.N.A., check the temperature

of your CPU using appropriate software (e.g. the respective

applications of your mainboard manufacturer), in order to

evade automatic throttling of the CPU due to the increased

temperature. If the cooling performance is insufficient, please

increase case ventilation or remove the U.L.N.A.

Attaching the fan

Step 7:

Attach the fans to the heatsink using the steel clips. The

NF-P12 120mm fan can be moved upwards or left off in order

to improve compatibility. If you don’t run the NF-P12 on the

CPU cooler, you can use the supplied fan screws or silicone

Vibration-Compensators to install it inside your case.

Ultra-Low-Noise Adapter

(U.L.N.A.) for NF-P12

Ultra-Low-Noise Adapter

(U.L.N.A.) for NF-P14

NH-D14

Installation Manual INTEL

For all enquiries concerning your Noctua cooler, both your

retailer and the international Noctua support team at

support@noctua.at are at your service.

Please also consult the FAQ section on our website

www.noctua.at.

Support & FAQs

As it is not possible to reliably calculate or control the forces

that act upon a system during transport (e.g. in shipping), we

generally recommend, for safety reasons, taking the cooler off.

Noctua cannot be held responsible for any damage that may

arise due to excessive stress during transport if you keep the

heatsink installed.

Should I take the cooler off before transporting

my system?

NH-D14

Installation Manual AMD

Required mounting parts:

First put the plastic spacers onto the screw threads, then fix

the mounting bars using the 4 long screws.

Attaching the mounting bars

Step 2:

Thank you very much for choosing a Noctua cooler. This

manual will guide you through the installation process of

the SecuFirm2

mounting system step by step.

Prior to installing the cooler, please consult the compat-

ibility list on our website and verify that the cooler is fully

compatible with your motherboard.

Should you encounter any difficulties, please check the

FAQs on our website and don’t hesitate to contact our

support team at . Noctua cannot support@noctua.at

be held responsible for any damage or losses caused by

compatibility issues.

Multilingual versions of this manual are available on our

website: www.noctua.at

Caution: Make sure that the curved sides of the mounting

bars are pointing inwards.

Noctua NH-D14 AMD

Installation Manual

Caution: Tighten the screws until they stop.

2x mounting bars

4x long screws

4x plastic spacers

Caution: The SecuFirm2

mounting system requires a backplate,

which is preinstalled on most AM2/AM2+/AM3 mainboards.

If your mainboard doesn’t have a backplate, please contact our

support team at support@noctua.at.

Step 3:

Applying thermal paste

If there are residual traces of thermal paste or thermal pads on

your CPU, please clean them off first.

Then press a small drop (4-5mm diameter) of NT-H1 onto the

centre of the heat-spreader.

Caution: Applying too much thermal paste will lower the heat

conductivity and cooling performance!

Removing the retention module

Step 1:

If your mainboard uses a retention module for CPU cooler

installation, please remove it first. The

SecuFirm2

mounting

system will install directly to your mainboard’s stock backplate

on the rear side of the socket.

AMD stock backplate

Step 4:

Fastening the heatsink to the CPU

Caution: Please take off the protection cover at the bottom side

of the heatsink first!

Take off the centre fan. Then put the heatsink onto the CPU and

screw it to the screw threads of the mounting bars.

Caution: Tighten the screws until they stop.

Produktspecifikationer

Varumärke:	Noctua
Kategori:	kylsystem för dator
Modell:	NH-D14
Vikt:	1240 g
Bredd:	140 mm
Djup:	158 mm
Höjd:	160 mm
Ljudnivå (låg hastighet):	12.6 dB
Material:	Aluminium, Cooper
Modell:	Heatsink/Radiatior
Luftflöde:	92.3 m³/h
Rotationshastighet (max):	1300 RPM
Medeltid mellan fel (MTBF):	150000 h
Rotationshastighet (min):	900 RPM
Spänning:	12 V
Fläkthastighet (max):	1300 RPM
Fläkthastighet (min):	900 RPM
Lagertyp:	Self-Stabilising Oil-pressure Bearing (SSO)
Produktens färg:	Brown, Silver
Förpackningstyp:	Låda
Antal per förpackning:	1 styck
Strömförbrukning (vanlig):	1.2 W
Fläktdiameter:	140 mm
Antal fläktar:	1 fläkt/-ar
Ljudnivå (hög hastighet):	19.8 dB
Lämplig placering:	Processor
Stödd processor uttag:	Socket AM2, Socket AM2+, Socket AM3, Socket AM3+, Socket FM1, Socket FM2
Mått, fläkt (B x D x H):	140 x 150 x 25 mm
Bottenplatta material:	Koppar
Kylarbredd:	140 mm
Kylardjup:	130 mm
Kylarhöjd:	160 mm
Kylarmaterial:	Aluminium
Fläktbrusnivå (max):	19.8 dB
Fan spänning:	12 V