Pyle PDA30BU Bruksanvisning
Läs gratis den bruksanvisning för Pyle PDA30BU (6 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 2.5 recensioner. Har du en fråga om Pyle PDA30BU eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/6
Wireless Stereo Power Amplifier BT Compatible
PDA30BU
Blue Series Compact and Audio Streaming Amp
with RCA & Speaker Terminals
www.PyleUSA.com
2
Read through this user manual before using the product
to ensure its correct use. Keep this manual for future reference.
Quick Setup:
1. Main Power ON Switch: Switch ON/OFF the amplier by using this switch.
2. --LINE input model --Wireless BT input model.Input LED: RED Green
3. MIC Input
4. Mic volume control: Use this control to set the volume level of Microphone.
5. Adjust to boost or cut LOW frequencies.BASS KNOB:
6. Adjust to boost or cut HIGH frequencies.TREBLE KNOB:
7. Master Volume: Adjusts main audio system volume level.
8. Lets you connect the desired LINE input source.RCA L/R LINE Input:
9. Speaker output (L/R)
10. AC IN
11. Wireless BT Antenna: Wireless BT Streaming receiver
Rear PanelFront Panel
www.PyleUSA.com
3
Setup and pairing (Wireless BT ampliers) are really easy. The following
instructions will help you connect Audio Ampliers to your music system or
pair with your tablet, computer, or smartphone.
1. Connecting the Speaker Wire
Audio stereo power ampliers that will power one pair of passive speakers
between 4 and 8 ohms (or subwoofer if you got the 2.1 CH amp or subwoofer
amp). To connect the amplier to your speakers you will need 2-conductor
stranded speaker wire. The ampliers use high-quality binding posts that will
accept heavy gauge bare wire banana plugs, spade lugs, or pin terminators.
If you use your own speaker wire we recommend using at least 16 gauge wire
and using the same length of wire from the amplier to each speaker It's also a
good idea to turn o your amplier before connecting power, audio sources or
speakers.
Preparing the Speaker Wire
1. Separate the last 3" of each speaker wire conductor.
2. Strip 1/2" of insulation from the end of each wire.
3. Twist the exposed copper strands with your ngers 3 or 4 times so the strands
stay together.
NOTE:
As you make your connections, be sure to connect the positive (+) terminals on
your amplier to the positive (+) terminals on your speakers. Even if your wire does
not have (+) or (-) markings, most 2-conductor speaker wire has printing on one
side to help you dierentiate between the wire pairs.
If you are Using Bare Wire
1. Use your thumb and nger to unscrew the binding post connectors on the back
of each speaker.
2. Insert each speaker wire into the holes on the side of the binding post connectors,
observing proper polarity.
3. Retighten the binding posts with your ngers.
4. The stripped portion of the wire should be secured rmly in each connector.
5. Make sure that none of the speaker wire strands have come in contact with an
adjoining terminal.
Produktspecifikationer
| Varumärke: | Pyle |
| Kategori: | mottagare |
| Modell: | PDA30BU |
Behöver du hjälp?
Om du behöver hjälp med Pyle PDA30BU ställ en fråga nedan och andra användare kommer att svara dig
mottagare Pyle Manualer
2 Juli 2025
6 Juni 2025
6 December 2024
6 December 2024
17 Oktober 2024
30 September 2024
25 September 2024
22 September 2024
21 September 2024
19 September 2024
mottagare Manualer
- Lindell Audio
- Pyle Pro
- Radial Engineering
- DAP
- Audio Pro
- Crest Audio
- Hotone
- NuPrime
- Music Hall
- BOYA
- Camille Bauer
- CyberData Systems
- SoundTube
- Kramer
- VMV
Nyaste mottagare Manualer
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025
1 Augusti 2025