Pyle PDWM5500 Bruksanvisning

Pyle mikrofon PDWM5500

Läs nedan 📖 manual på svenska för Pyle PDWM5500 (3 sidor) i kategorin mikrofon. Denna guide var användbar för 3 personer och betygsatt med 5.0 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/3

PDWM5500

OPERATING INSTRUCTIONS

WIRELESS MICROPHONE SYSTEM

PO WE R

P W M A5 0 00 P R O FE S SI O NA L WI RE LE SS M I C RO P HO NE S YS TE M

.........SPECIFICATION.........

1) Carrier Frequency:.................... VHF 160-280MHz

2) Frequency Stability:.....................0.005%

3) Modulation mode:.....................VHF

4) Audio Frequency Response:................60Hz-16KHz

5) Signal to Noise Ratio:...................>60dB

6) Maximum Sound Pressure Level:..............>100dB

7) Distortion:........................<0.5%

8) Operating Range:.....................Approx 240 ft.

System Specifications

1) RF Output Power: .....100mW MAX

2) Harmonic Suppression:...................40dB

3) Antenna:.........................Builtin

4) Power Supply:.......................1.5V(AA) x3

5) Nominal Current Drain:...................Approx. 15mA

6) Battery Life:........................Approx. 12 hours

................

Transmitter

1) Receive Mode:......................Crystal Frequency Lock

2) Sensitiity:.........................40dBu(S/N=60dB)

3) SignaltoNoise Ratio:....................>60dB

4) Audio Output Level:....................400mV Max

5) Power Supply:.......................AC110V/220V(.10%) DC12v-18v/500mA

Receiver

- 4 -

Thank you for selecting the PDWM5500 4 Mic VHF Wireless System. Before operating please read this instruction manual carefully

and thoroughly in order to understand the correct operating procedures and achieve the best results.

1) Plug the included audio cable into the receiver's mixed output connector, and the other end into a mixer or power amplifier system.

Extend the two antennas fully to the vertical position. Switch on the receiver. The POWER ON light will illuminate.

2) Open the battery cover of the microphone and install the batteries inside the compartment properly. Replace the cover.

3) Position the transmitter power switch to ON. The indicator light will illuminate. The microphone features a 3-way power switch. The

middle position (standby) functions as a mute switch.

4) The receiver's corresponding channel light will illuminate, indicating reception.

5) Adjust the volume knobs of the receiver and power amplifier.

6) When the transmitter power indicator dims, it indicates low battery power. Replace the batteries.

- 1 -

...........PREFACE...........

FEATURES:

SYSTEM SETUP

ALC circuit to eliminate distortion:

Frequency compressing/expanding (companding) circuitry to lower noise and increase the dynamic range.

Superior squelch and high signal to noise ration.

Near zero noise output when on standby.

Wide frequency response range and low distortion.

Convenient operation status indicators.

LED Displays.

Multiple HF and MF narrowband filters to eliminate interfering signal.

Low power consumption components to ensure longer battery life.

Special impact wave eliminating circuit for microphone switch.

Long transmitting distance-up to 240 ft. in ideal circumstances.

REAR PANEL OF RECEIVERFRONT PANEL OF RECEIVER

- 2 -

.....RECEIVER AND TRANSMITTER.....

1) Power Indicator

2) Power Switch

3) CH.A Volume Control

4) CH.A/B LED Displays

5) CH.B Volume Control

6) CH.A/B AF Meters

7) CH.C/D AF Meters

8) CH.C Volume Control

9) CH.C/D LED Displays

10)CH.D Volume Control

11) CH. C/D Antenna Connector

12) Individual Audio Output

13) Mixed Audio Output

14)CH.A/B Antenna Connector

15)AC Power Input (voltage selectable)

1 3 4 5 6 7 8 9 10

POW ER

PW MA 50 00 PRO FE SS IO NA L WI RE LE SS MI CRO PH ON E S YS TEM

11 12 14

ANT.CD MIX OUT ANT.ABOUT.D OUT.C OUT.B OUT.A BALANCED DC13V/500mA

1) Grill

2) Power Switch

3) LED Power Indicator

4) Mic Body

5) Battery Compartment

- 3 -

.....RECEIVER AND TRANSMITTER.....

Description

Troubleshooting

1 2 3 4 5

1. Unit does not turn on.

Make sure the power cable is connected properly.

Check the fuse.

Check the voltage selector

2. AF display moves, but there is no sound output.

Check volume level.

Check audio cable.

Check the settings on your amplifier.

3. The effective receiving distance decreases.

Change batteries.

Check for any devices that may be causing interference.

4. Sound Quality Deteriorates

Change Batteries.

Check for any devices that may be causing interference.

Do not use two machines with the same frequency at the same time.

Caution:

Do not open the unit. There are no user serviceable parts

inside. Refer service to a qualified technician.

Produktspecifikationer

Varumärke:	Pyle
Kategori:	mikrofon
Modell:	PDWM5500
Ljudutgång:	6,3 mm
Modell:	Scenmikrofon
Maximal räckvidd:	100 m
Innehåll:	4 Mic.
Driftspänning:	0.4 V
Mikrofonfrekvens:	60 - 16000 hz
Batteriteknik:	Alkalisk
Batterityp:	AA
RF-effekt:	100 mW
Dynamiskt omfång:	100 dB
Frekvensstabilitet:	0.005 %
Produktens färg:	Svart
Skrivbordsstativ:	Nej
AC-inspänning:	110-220 V
USB-ström:	Nej
Anslutningsteknologi:	Trådlös
Växelström Frekvens:	50 - 60 hz
På / av-knapp:	Ja
Batterispänning:	1.5 V
Modulator:	FM
Plug & Play-kompatibel:	Ja
Nätaggregatstyp:	AC/DC
Mikrofon känslighet (utnivå):	40 dB
Arbetsfrekvens:	160 - 280 MHz
Drifttid för batteri:	12 h
Signal/brusförhållande (SNR):	60 dB
Mikrofon, riktning:	Riktad
Mottagare medföljer:	Ja
Anslutning:	1/4", XLR
Tekniska egenskaper:	110V/220V
Mikrofon, riktningstyp:	3