Rane GE 130 Bruksanvisning
Sidor 4 blandningskonsoler
Läs bruksanvisningen för Rane GE 130 gratis online eller ladda ner PDF:en. 47 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
Manual-1
OPERATORS MANUALGE 130
GRAPHIC EQUALIZER
GE 130 CONNECTION
When first connecting the GE 130 to other components,
leave the power supply for last. This gives you a chance to
make mistakes and correct them without damaging your
fragile speakers, ears and nerves.
INPUTS
Both XLR and Euroblock Inputs are wired in parallel and
are actively balanced. Each works equally well. Choose
strictly from a required hardware point-of-view, there will be
no performance trade-offs. The wiring convention adheres to
American, British and International standards of pin 2 (+) hot,
pin 3 (–) return, and pin 1 shield. Unbalanced operation
involves using only pin 2 or “+” as signal, and pin 1 as shield
or ground. It is not necessary to short any inputs to ground—
it doesn’t hurt, it’s just not necessary. Use pin 1, or the shell,
for shield ground.
QUICK START
So tell me honestly, do you actually read the manuals or do you just want to connect the thing and go? If you are one
of the “gotta go now” crowd please read this short section. Even if you read slowly so as to savor every syllable, it only
takes a couple of minutes and may save more of your valuable time later. The rest of this manual is dedicated to those who
really want to know all the nitty-gritty details.
Wait a minute before plugging in the power supply. Hopefully the equipment to and from the GE 130 is balanced, with
pin 2 “hot.” From the line level output preceding the GE 130, connect a XLR male connector to the INPUT jack on the rear
of the GE 130. Connect a female XLR connector to the OUTPUT jack on the rear of the GE 130, to the next line level
device in the signal chain.
Now plug in the power supply. The yellow POWER LED should illuminate, and if you have an audio source working
and the rest of the signal chain completed, you will hear audio. With sliders centered and the LEVEL control at “7”
(corresponds to about 2 o’clock), depress the BYPASS switch. If any difference in level exists, adjust the LEVEL control
so the same volume exists whether BYPASS is in or out. You now have an expensive jumper wire. Fully utilizing the
capabilities of the GE 130 requires moving some of the sliders, but you already knew that. To make best use of the GE 130,
use some sort of an analyzer to adjust the sliders properly.
Never connect anything except an RS 1 or other approved Rane AC power supply to the thing that looks like a
telephone jack on the rear of the unit. This is an AC supply and requires some special attention if you do not have an
operational power supply exactlylike the one that was originally packed with your unit.
OUTPUTS
The Outputs mimic the Inputs. Balanced output requires
using pin 2 or “+”, and pin 3 for the signal ground. It does not
require pin 1 or shield. The signal exists differentially
between the two balanced leads; ground is not involved. For
hum-free systems ground is used only for shielding.
SIGNAL LEVELS
Signal levels from -10 dBV to +4 dBu are considered
normal and within range (at least 20 dB of headroom exists
above these levels). Do not directly connect microphones
into the GE 130. These require a mic preamp.
WEAR PARTS: This product contains no wear parts.
Produktspecifikationer
| Varumärke: | Rane |
| Kategori: | blandningskonsoler |
| Modell: | GE 130 |
Behöver du hjälp?
Om du behöver hjälp med Rane GE 130 ställ en fråga nedan och andra användare kommer att svara dig
blandningskonsoler Rane Manualer
Rane NM 48 Bruksanvisning Rane GQ 15 Bruksanvisning Rane MQ 15/30 Bruksanvisning Rane MM 8z Bruksanvisning Rane ME 30B Bruksanvisning Rane GE 14 Bruksanvisning Rane PE 15 Bruksanvisning Rane MQ 302S Bruksanvisning
Alla Rane blandningskonsoler manualer
Populära i blandningskonsoler
blandningskonsoler Manualer
Nyaste blandningskonsoler Manualer
Samson XML410 Bruksanvisning Toa A-3648D Bruksanvisning Solid State Logic Origin Bruksanvisning Solid State Logic Matrix Bruksanvisning Kenwood HM680 Bruksanvisning Solid State Logic UF8 Bruksanvisning Kenwood kMix HM808 Bruksanvisning Scarlett SC-HM40S16 Bruksanvisning Radial Engineering Key-Largo Bruksanvisning Glemm MMX 54ZM Bruksanvisning